Genie PowerLift Excelerator Owner's Manual - Page 4

Check Step 3, Check Step 4

Page 4 highlights

Check Step 3: Measure Garage Door Height Measure garage door height (7'-6", 8'-0", or taller) with tape measure. A If door height is 7'-6" or less, continue with Check Step 4. B If door height is 8'-0", you need an Excelerator Rail Extension Kit. (Figure 3) (See Accessories Order Form, page 31/32). C If door height is taller than 8'-0", the Excelerator you pur chased is the wrong version. Contact your Genie Customer Service Representative at 1-800-35-GENIE. Ch ec k Ste p 4: Check Door Header Area NOTE The header is a heavily reinforced section of the wall just above the top of the garage door opening. A Find vertical center line of door and header: • Close door Measure door width at top. • Mark a point at center of door and on header directly above door. Draw a center line to connect points. B Find Header Bracket mounting height (Figure 4): (Do not attach Header Bracket). • Raise door, watching top edge of door and stop door when its edge reaches its highest point. • Measure distance ("H") from top edge of door to floor. - For sectional doors, add 2-1/2" to "H". Mark a point on center line. Bottom of Header Bracket will be installed here. - For one-piece doors, add 6" to "H". Mark this point on center line. Bottom of Header Bracket will be installed here. NOTE • For both types of doors: - If the ceiling in your garage is so low that there is not at least a 3" space above the Header Bracket mounting point, contact a Genie Factory Authorized Dealer. • If a door spring is in the way, place the Header Bracket avove the spring. Do Not move the door spring. C Check wall for a stud or a solid header at your mark: (If checking a finished wall, a stud finder may be helpful). • If location is above Header, a 2" x 6" board must be screwed to studs beside your mark with at least two Lag Screws and Flat Washers (not provided). • Transfer your mark to new mounting board. Rail Extension for 8' door Figure 3 Rail Extension Kit SECTIONAL DOOR ONE-PIECE DOOR Figure 4 Find Highest Point of door travel 4 For Help, call 1-800-35-GENIE or visit www.geniecompany.com

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30

4
For Help, call 1-800-35-GENIE or visit www.geniecompany.com
M
EASURE
G
ARAGE
D
OOR
H
EIGHT
Measure garage door height (7’-6”,
8’-0”,
or taller) with
tape measure°
A
If door height is 7’-6” or less, continue with Check Step 4°
B
If door height is 8’-0”,
you need an Excelerator Rail Extension
Kit. (
Figure 3
) (See Accessories Order Form, page 31/32)°
C
If door height is taller than 8’-0”, the Excelerator you pur
chased
is the wrong version° Contact your Genie Customer
Service Representative at
1-800-35-GENIE
°
Check Step 3:
C
HECK
D
OOR
H
EADER
A
REA
A
Find vertical center line of door and header:
Close door°
Measure door width at top°
Mark a point at center of door and on header directly
above door°
Draw a center line to connect points°
B
Find Header Bracket mounting height
(
Figure 4
):
(Do not attach Header Bracket)°
Raise door, watching top edge of door and stop door
when its edge reaches its highest point°
Measure distance (“H”) from top edge of door to floor°
For sectional doors, add 2-1/2” to “H”°
Mark a point
on center line°
Bottom of Header Bracket will be
installed here°
For one-piece doors, add 6” to “H”°
Mark this point
on center line°
Bottom of Header Bracket will be
installed here°
C
Check wall for a stud or a solid header at your mark:
(If checking a finished wall, a stud finder may be helpful)°
If location is above Header, a 2” x 6” board must be
screwed to studs beside your mark with at least two Lag
Screws and Flat Washers (not provided)°
Transfer your mark to new mounting board°
Check Step 4:
NOTE
The header is a heavily reinforced section of the wall just
above the top of the garage door opening°
NOTE
For both types of doors:
– If the ceiling in your garage is so low that there is
not at least a 3” space above the Header Bracket
mounting point, contact a Genie Factory
Authorized Dealer°
If a door spring is in the way, place the Header
Bracket avove the spring°
Do Not
move the door spring°
Rail Extension for
8’ door
Figure 3
Rail Extension Kit
Figure 4
Find Highest Point of door travel
SECTIONAL DOOR
ONE-PIECE DOOR