Harman Kardon DPR 1001 Owners Manual - Page 32

32

CONFIGURING THE REMOTE

Multiroom Operation

When operating the DPR 1001 from a remote room

location where an IR sensor link has been connected to

the DPR 1001’s rear-panel

Multiroom IR Input

£

,

you may use either the main remote control or the

Zone II remote. To turn on the multiroom feed, press any

of the

Input Selector

buttons on the Zone II remote

ç∂

or the main remote

d

. Press the

AVR Selector

e

∫

to turn the unit on to the last

source, or any of the other Selector buttons to turn on to

a specific source.

As long as an IR feed to the DPR 1001 has been estab-

lished from the remote room, using any of the buttons

on either remote will control the remote location volume

r

î

, change the tuner frequency

w

É

, change

the tuner preset

v©

or mute the output

.

If the DPR 1001’s

Remote IR Output Jack

¢

is con-

nected to an IR Input jack on compatible Harman Kardon

audio components such as CD, DVD or cassette players,

the transport functions of those machines may also be

controlled using the

Transport Controls

qst

ux

Éƒ©˙∆

on either remote

control.

To turn the system off from the remote room, press

the

Power Off Button

a

å

. Remember that the

DPR 1001 may be turned on or off from the remote

room, regardless of the system’s operation or status in

the main room.

NOTE:

When the tuner is selected as the source for the

remote zone, any change to the frequency or preset will

also change the station being listened to in the main

room, if the tuner is in use there. Similarly, if someone in

the main room changes the station, the change will also

impact the remote room.

To activate the feed to the remote room, while you are in

the main listening room where the DPR 1001 is located,

press the

Multiroom Button

`

on the remote. Next,

press the

Set Button

p

. Press the

⁄

/

¤

Navigation

Buttons

n

to turn the multiroom feed on or off. When

the multiroom system is on, the

Multi Indicator

C

will

light in the

Main Information Display

^

, and the

Lower Display Line

B

and OSD will display

MULTI

ON

. Press the

Set Button

p

to enter the setting.

When the multiroom system is turned on, the input

selected using the multiroom menu will be fed to the

Multiroom Output Jacks

ª

on the rear panel. The

volume will be as set in the previous selection, although

it may also be adjusted using an optional IR sensor and

the Zone II remote in the remote location or on the

optional audio power amplifier connected to the

Multiroom Output Jacks

ª

.

Once the multiroom system is turned on, it will remain on

even if the DPR 1001 is placed in the Standby mode in

the main room by pressing the

Power Off Button

å

a

or the

On/Standby Button

2

. To turn off

the multiroom system, even when the DPR is in Standby

mode in the main listening room, press the

Multiroom

Button

`

and then the

Set Button

p

. Press the

⁄

/

¤

Navigation Buttons

n

so that the

Multiroom

Indicator

C

goes out, and the

Lower Display Line

B

and OSD will display

MULTIOFF

. Press the

Set Button

p

to enter the setting and turn the unit off.

Even when the DPR 1001 is turned off in the main room,

the multiroom system may be turned on at any time by

pressing the

Multiroom Button

`

, or any of the

Selector Buttons

∫ç∂

in the remote room.

Configuring the Remote

The DPR 1001 remote is factory-programmed for

all functions needed to operate the unit. In addition,

it is also preprogrammed to operate most recent

Harman Kardon DVD players and changers, CD

players and changers, CD recorders and cassette

decks. The codes for other brand devices may be

programmed into the DPR 1001 remote using its

extensive library of remote codes or a head-to-head

learning process for codes not in the internal library.

Thanks to the remote’s advanced technology and

two-line LCD display, it is no longer necessary to

look up cumbersome codes when programming the

remote; following the steps outlined below, you simply

search for the brand name from the remote’s memory.

We recommend that you first try the preprogrammed

code entry method. If that procedure is not successful,

then try the code learning method.

Preprogrammed Code Entry

The easiest way to program the DPR remote for

operation with a source device from another brand

is to follow these steps:

1. Turn on the power to the device you wish to pro-

gram into the DPR remote. This is important, as in a

later step you will need to see whether the device

turns off to determine whether the remote has been

programmed for the proper remote codes.

2. Press and hold the

Program Button

y

for

about three seconds while the message shown

in Figure 15 appears in the remote’s

LCD

Information Display

c

. Release the button

when the red light under the

Set Button

p

appears.

Figure 15

3. The remote’s

MAIN MENU

message

(Figure 16), will appear in the LCD display and

the

Set Button

p

will remain illuminated

in red. Press the

Set Button

p

to begin

the process of selecting a device and locating

the proper remote codes.

Figure 16

4.

SELECT A DEVICE

will appear in the LCD

display (Figure 17). Press the

⁄

/

¤

Navigation

Buttons

n

to scroll through the list of device

categories and press the

Set Button

p

when

the device you wish to set the codes for appears.

For this example, we will select “TV” to enter the

codes needed to operate your TV.

Figure 17

NOTE:

The codes for hard-drive recorder products

(PVR) such as TiVo and Replay are programmed by

selecting VCR as the device. For satellite-based TiVo

products, check under the brand name of the product.

5. At the next menu screen on the remote (Figure

18) press the

Set Button

p

to enter the

Manual mode, which means that you will select

the brand name of the device from the list pro-

grammed into the remote’s memory.

Figure 18

6. The next menu screen on the remote (Figure 19)

will show the start of the list of available brands.

Press the

⁄

/

¤

Navigation Buttons

n

until

the brand name of the device you are program-

ming into the remote appears on the lower line of

the display and then press the

Set Button

p

.

Figure 19

NOTE:

If the brand name for the product you wish to

program does not appear in the list, the codes may

still be available, as some manufacturers share codes.

If the desired brand is not listed, press the

Clear

Button

j

to exit the programming process,

and skip to the instructions shown on page 33 for the

“Automatic” method of programming the remote. If

desired, or if the codes for your brand are not part

of the remote’s library at all, you may still use the DPR

remote to program most infrared-controlled products

by “learning” the commands from the product’s

original remote into the DPR remote. The instructions

for Learning Commands are on page 34.

7. The next step is important, as it determines which

codes will operate the source device or display.

Point the DPR remote at the device being pro-

grammed and, following the instructions shown in

the remote’s

LCD Information Display

c

,

press and release the

Numeric Keys

k

shown

SELECT BRAND

RCA

PROGRAM DEVICE

MANUAL

SELECT A DEVICE

TV

MAIN MENU

PROGRAM DEVICE

HOLD PROG BUTTON

FOR 3 SECONDS

33

43

34

CONFIGURING THE REMOTE

Harman Kardon DPR 1001 Owners Manual - Page 32

Configuring The Remote

Page 32 highlights