Harman Kardon DPR 1001 Owners Manual - Page 38

38

CONFIGURING THE REMOTE

of the bottom line and the

PUNCH-THROUGH

device. In the example used, the display to return the

remote to default settings will appear as shown in

Figure 53.

Figure 53

Channel Punch-Through

Channel punch-through allows the Channel Up/Down

buttons to send commands to a different device than

the one that has been selected for other commands.

For example, you may wish to use a cable box or

satellite receiver as the source for a VCR, so you

would want the

Channel Up/Down Selectors

¸

to transmit commands to the cable box even though

the other button commands are programmed to

operate the VCR.

To program the DPR for Channel punch-through,

follow these steps. This example will show how to pro-

gram channel punch-through so that the commands

programmed for Channel Up/Down for the VID 3/

Cable device will be transmitted when the VID 1/VCR

device has been selected as the current device.

1. Press and hold the

Program Button

O

for

about three seconds while the message shown

in Figure 15 appears in the remote’s

LCD

Information Display

2

. Release the button

when the red light under the

Set Button

F

appears.

2. The remote’s

MAIN MENU

message (Figure

16), will appear in the LCD display and the

Set

Button

F

will remain illuminated in red. Press

the

⁄

/

¤

Navigation Buttons

n

until

PUNCH-THROUGH

appears on the bottom

line of the LCD screen, as shown in Figure 49.

Press the

Set Button

F

to enter the main

punch-through menu branch.

3. At the next menu screen, press the

⁄

/

¤

Navigation Buttons

n

until

CHANNEL

appears on the bottom line of the LCD screen,

as shown in Figure 54. Press the

Set Button

F

to begin programming the remote for

Channel punch-through.

Figure 54

4. The next display screen (Figure 55) is where you

select the device that will receive the punch-

through commands. In our example, that is the

VID 2/TV button, as that is where we want the

cable box’s channel controls to be active. Press

the

⁄

/

¤

Navigation Buttons

n

until the

name of the base device appears and then press

the

Set Button

F

.

Figure 55

5. At the next display screen (Figure 56), you will

select the device whose Channel Up/Down com-

mands will be used. Press the

⁄

/

¤

Navigation

Buttons

n

until the desired device name

appears to the right of the device in use. In our

example, that is the cable box. When the desired

combination of devices appears, press the

Set

Button

F

.

Figure 56

6. When the Set button is pressed, the display will

change to show you that the new combination

of control commands is being saved to the unit’s

memory, as shown in Figure 57. The word

SAVED

will flash four times and then the remote

will return to normal operation.

Figure 57

7. Once the punch-through is programmed, the

channel up/down buttons of the second device

named will be used when those buttons

¸

are

pressed while the master device is in use.

Returning the Channel Control Settings to

Default Operation:

If you wish to remove the Channel Punch-Through

so that the commands for Channel Up/Down are

returned to the factory default setting, follow the steps

shown above, except that in Steps 4 and 5, select

the same device for both the

DEVICE IN USE

on

the left side of the bottom line and the

PUNCH-

THROUGH

device. In the example used, the display

to return the remote to default settings will appear as

shown in Figure 58.

Figure 58

Transport Punch-Through

Transport punch-through allows the

Play

q

, Stop

J

, Fast Forward/Reverse

I

, Pause

J

,

Record

J

and

Skip Up/Down

K

buttons to

send commands to a different device than the one

that has been selected for other commands. For

example, you may wish to operate the transport of a

second VCR you have connected to the VID 2/TV

input, as shown in the following example.

1. Press and hold the

Program Button

O

for

about three seconds while the message shown

in Figure 15 appears in the remote’s

LCD

Information Display

2

. Release the button

when the red light under the

Set Button

F

appears.

2. The remote’s

MAIN MENU

message (Figure

16), will appear in the LCD display and the

Set

Button

F

will remain illuminated in red. Press

the

⁄

/

¤

Navigation Buttons

n

until

PUNCH-THROUGH

appears on the bottom

line of the LCD screen, as shown in Figure 48.

Press the

Set Button

F

to enter the main

punch-through menu branch.

3. At the next menu screen, press the

⁄

/

¤

Navigation Buttons

n

until

TRANSPORT

appears on the bottom line of the LCD screen, as

shown in Figure 59. Press the

Set Button

F

to begin programming the remote for transport

punch-through.

Figure 59

4. The next display screen (Figure 60) is where you

select the device that will receive the punch-

through commands. In our example, that is the

TV button, as that is where we want the VCR’s

transport controls to be active. Press the

⁄

/

¤

Navigation Buttons

n

until the name of the

base device appears and then press the

Set

Button

F

.

Figure 60

5. At the next display screen (Figure 61), you will

select the device whose transport commands will

be used. Press the

⁄

/

¤

Navigation Buttons

n

until the desired device name appears to the

right of the device in use. In our example, that is

the VCR. When the desired combination of

devices appears, press the

Set Button

F

.

Figure 61

6. When the Set button is pressed, the display will

change to show you that the new combination of

control commands is being saved to the unit’s

memory, as shown in Figure 62. The word

SAVED

will flash four times and then the remote

will return to normal operation.

Figure 62

TV

<

-VCR [TRS]

SAVED

PUNCH-THROUGH

TV

<

-VCR

DEVICE IN USE

TV

PUNCH-THROUGH

TRANSPORT

PUNCH-THROUGH

VCR

<

-VCR

VCR

<

-CBL [CHAN]

SAVED

PUNCH-THROUGH

VCR

<

-CBL

DEVICE IN USE

VCR

PUNCH-THROUGH

CHANNEL

PUNCH-THROUGH

TV

<

-TV

CONFIGURING THE REMOTE

Harman Kardon DPR 1001 Owners Manual - Page 38

Punch-through, Main Menu, Channel, Saved, Device In Use, Punch, Through, Transport

Page 38 highlights