Harman Kardon DPR 1001 Owners Manual - Page 36
Erasing a Macro
View all Harman Kardon DPR 1001 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 36 highlights
CONFIGURING THE REMOTE your system, changing devices or other common tasks. Thanks to the remote's two-line display, it is easier than ever for you to take advantage of the power of macro commands. Recording a Macro To record a macro into the remote's memory, follow these steps: 1. Press and hold the Program Button y for about three seconds while the message shown in Figure 15 appears in the LCD Information Display 2. Release the button when the red light under the Set Button F appears. 2. The MAIN MENU message (Figure 16), will appear in the LCD display and the Set Button F will remain illuminated in red. Press the ⁄ Navigation Button D three times so that MACRO appears on the bottom line of the LCD screen, as shown in Figure 37. Press the Set Button F to enter the main macro menu. MAIN MENU MACRO Figure 37 3. At the next menu screen (Figure 38) press the Set Button F to begin recording a macro. MACRO RECORD A MACRO Figure 38 4. The next display screen (Figure 39) is where you select the button that will be used to recall the macro. The choices are the Power On Button 1 or one of the discrete Macro Buttons R. Press the ⁄/¤ Navigation Buttons n until the name of the button you wish to program the macro into is shown and press the Set Button F. For this example we will show how to program a series of commands that will be sent when the Power button is pressed. RECORD A MACRO POWER ON Figure 39 5. The next screen that appears (Figure 40) is where you select the device for the first command that will be sent out as part of the macro. Press the ⁄/¤ Navigation Buttons n until the name of the device appears in the lower line in the LCD display. For this example, the first button we want to have the macro "press" is the Power On button, so the AVR device is selected. Press the Set Button F when the desired device name appears to move to the next programming step. SELECT A DEVICE AVR Figure 40 6. The next display (Figure 41) is where you begin entering the individual commands for the macro, in the order you wish them to be transmitted. Remember that when you want to change devices, you must first press the Input Selector de for that button, and then press the Command or Function key. Since we want to program a series of events that occur each time the Power On button is pressed, press the AVR button. In your specific macro, this is the first command button. SELECT A DEVICE AVR Figure 41 7. The next display (Figure 42) and the subsequent screens are where the actual macro programming take place. The words at the left side of the top line of the display show the button that is being programmed (e.g., the Power On Button 1 or one of the Macro Buttons R) and the indication at the right side of the top line shows the number of macro steps available of 20 possible steps. Following the instructions on the remote's LCD screen, press the first key you wish to be transmitted in the macro. In our example, we first want the DPR to turn on, so the Power Button 1 should be pressed. POWER ON 00/20 SELECT KEY PRESS Figure 42 8. Once the first command button for the macro has been pressed, continue to press the buttons you wish to be part of the macro, in the order they will be used. Press each button within five seconds of the last button, remembering to press the Input Selector 34 when you are changing device functions. As the buttons on the remote are pressed, the remote's display screen will show the steps in the macro as they are programmed (Figure 43). [AVR] [AVR] POWER ON Figure 43 9. For our example, we first want the AVR Power On button pressed, followed by the TV Power On, followed by the Cable Box On, followed by the selection of the Logic 7 mode. To do that, press the buttons in this order: • Power On 1 • VID 2/TV 3 • Power On 1 • VID 3/Cable 3 • Power On 1 • AVR 4 • Logic 7 7 As each button is pressed to enter it into the macro you will see the button names appear and then scroll up on the LCD display as your confirmation of the key entry (Figure 43). 10. When all commands for the macro have been entered, press the Set Button F to save the macro. The display screen will show the button to which the macro has been programmed and the number of steps used, and the word SAVED will blink four times in the lower line of the LCD display. When the display returns to normal, the macro has been entered and the remote is ready for operation. 11. If a macro has been programmed into the Power On Button 1, it will play back anytime the Power On button is pressed. As the macro plays, you will see the steps appear in the remote's LCD display. Macros programmed into one of the four discrete Macro buttons may be activated at any time by pressing the appropriate button. Erasing a Macro Once a macro has been created and stored in the DPR remote's memory, you have the option of erasing it. You may do this at any time by following these steps: 1. Press and hold the Program Button O for about three seconds while the message shown in Figure 15 appears in the remote's LCD Information Display 2. Release the button when the red light under the Set Button F appears. 2. The remote's MAIN MENU message (Figure 16), will appear in the LCD display and the Set Button F will remain illuminated in red. Press the ⁄ Navigation Button D three times so that MACRO appears on the bottom line of the LCD screen, as shown in Figure 37. Press the Set Button F to enter the main macro menu branch. 3. At the next menu screen (Figure 44) press ⁄/¤ Navigation Buttons n until the bottom line in the remote's LCD display reads ERASE A MACRO, as shown in Figure 44. Press the Set Button F to begin the process of erasing a macro. MACRO ERASE A MACRO Figure 44 36 CONFIGURING THE REMOTE