Harman Kardon DPR 1001 Owners Manual - Page 40

CONFIGURING THE REMOTE by the new button will appear. Following our example, the next letter needed is a "D," so you would press the "3" button once. b. To enter a letter that uses the same numeric key, you must first press the › Navigation Button D to move the blinking cursor block to the next position. Then press the Numeric Key A as required to enter the desired letter. c. To enter a blank space, press the › Navigation Button D twice. The first press will move the cursor to the right, and the second press will move the cursor one more space to the right, leaving a blank space between the last letter and the next one. 8. Repeat Step 7 as needed to enter all the needed letters, numbers, characters and spaces. 9. When the text entry is complete, press the Set Button F. The LCD display will blink DEVICE RENAMED three times and then return to normal operation. Once a device is renamed you will see the new name on the top line of the remote's LCD display whenever the Input//Device Selector 3 is pressed, or when any other command/function button on the remote is pressed after the main Device Selector is pressed. Note that renaming a device in the remote will not change the name of the input used by the on-screen menu system of the DPR. NOTES ON RENAMING DEVICES: • To move the cursor to the right or left of the display during the renaming process, press the ‹/› Navigation Buttons D as required. • The table below shows the letters, numbers and characters that may be accessed by pressing the Numeric Keys: Key Characters Key Characters 1 [,],/,1 6 M,N,O,6 2 A,B,C,2 7 P,Q,R,S,7 3 D,E,F,3 8 T,U,V,8 4 G,H,I,4 9 W,X,Y,Z,9 5 J,K,L,5 0 -,.,#,0 • Renaming a device changes the name of the device only, not any of the individual key functions within that device memory. To change the name of an individual device, follow the instructions in the next section. Renaming Individual Keys Thanks to the programming flexibility of the DPR remote, an individual button on the remote may be assigned a feature or function that is different from the name that appears as the factory default when the button is pressed. However, with the Rename Key function it is possible to rename almost any button on the remote so that when the button is pressed you will see a more descriptive or appropriate name displayed. To rename a specific button on the remote, follow these steps. For this example, we will show you how to rename the Tone Control Button V, which is normally not used when DVD is selected so that it reads ZOOM in the remote's display. 1. Press and hold the Program Button O for about three seconds while the message shown in Figure 15 appears in the remote's LCD Information Display 2. Release the button when the red light under the Set Button F appears. 2. The remote's MAIN MENU message (Figure 16), will appear in the LCD display and the Set Button F will remain illuminated in red. Press the ⁄/¤ Navigation Buttons n until RENAME appears on the bottom line of the LCD screen, as shown in Figure 66. 3. At the next menu screen press the ⁄/¤ Navigation Buttons n until RENAME KEY appears on the bottom line of the LCD screen, as shown in Figure 69. Press the Set Button F to continue. RENAME RENAME KEY Figure 69 4. The next display screen (Figure 70) is where you select the device within which the key to be renamed exists. Press the ⁄/¤ Navigation Buttons n until the name of the base device appears. In our example, since we want to rename a button within the DVD device memory, DVD should appear in the lower line of the LCD. When the desired device name appears, press the Set Button F. SELECT A DEVICE DVD Figure 70 5. At the next menu screen you will select the first button within the device to be renamed, as instructed in the display shown in Figure 71. Select the button by simply pressing it on the remote. SELECT A KEY Figure 71 6. Depending on whether or not the button pressed already has a named function within the device selected, one of two things will happen. a. If the button to be renamed already has a preprogrammed, or previously renamed title in the remote's memory, you will see that name on the top line of the LCD display, and a blinking block cursor will appear on the far left side of the bottom line of the display, as shown in Figure 72. b. If the button to be renamed does not have a function in the device selected, the top line of the LCD screen will be blank, and a blinking block cursor will appear on the far left side of the bottom line of the display, as shown in Figure 73. DISC SKIP Figure 72 Figure 73 7. To enter the new name for the key, press the Numeric Keys A. The letters above the numbered buttons indicate which letters or symbols will appear when the button is pressed during the renaming process. The first press of the button will enter the first character shown, subsequent presses of the same button will change the display to the other letters above that numbered key. For example, since the first letter we need to rename the Tone button to Zoom is a "Z," so you would locate the "Z" above the "9" button, and press the button four times. The first press shows a "W," the subsequent presses step through the other letters available until the "Z" appears. Consult the table on this page to see which characters are available by pressing a particular button. 8. After you enter the first letter of the new device name, there are three options for entering the next character: a. To enter a letter that requires a different numeric key to be pressed, simply press that button. The cursor will automatically move to the next position and the first letter accessed by the new button will appear. Following our example, the next letter needed is an "O," so you would press the "6" button once. b. To enter a letter that uses the same numeric key, you must first press the › Navigation Button D to move the blinking cursor block 40 CONFIGURING THE REMOTE