Harman Kardon DPR 1001 Owners Manual - Page 39

CONFIGURING THE REMOTE

39

7. Once the punch-through is programmed, the

transport buttons of the second device named

will be used when those buttons are pressed

while the master device is in use.

Returning the Transport Control Settings to

Default Operation:

If you wish to remove the Transport Punch-Through so

that the transport commands are returned to the fac-

tory default setting, follow the steps shown above,

except that in Steps 4 and 5, select the same device

for both the

DEVICE IN USE

on the left side of the

bottom line and the

PUNCH-THROUGH

device. In

the example used, the display to return the remote to

default settings will appear as shown in Figure 63.

Figure 63

EzSet Configuration

Harman Kardon’s patented EzSet feature makes it

easier than ever to calibrate the output levels on your

new DPR for maximum playback accuracy. In addition

to automatically setting the levels, the DPR remote’s

LCD display allows the unit to be used as a direct

read-out SPL meter. Complete instructions for using

the EzSet features of the DPR remote are found on

pages 22 and 23 of this owner’s manual.

In most cases you will find it easier to access the

EzSet capabilities directly by pressing the

SPL Select

Button

Á

and following the menu prompts as

detailed in pages 22 and 23. However, there is one

function of the remote that is only available through

the remote’s menu system being described in this

section.

To avoid having the calibration settings created with

EzSet changed accidentally, the remote allows you to

disable the

SPL Select Button

Á

on the remote.

To de-activate the button, follow these steps:

1. Press and hold the

Program Button

O

for

about three seconds while the message shown

in Figure 15 appears in the remote’s

LCD

Information Display

2

. Release the button

when the red light under the

Set Button

F

appears.

2.

The remote’s

MAIN MENU

message (Figure 16),

will appear in the LCD display and the

Set Button

F

will remain illuminated in red. Press the

⁄

/

¤

Navigation Buttons

n

until

SET

SPKR LEVELS

appears on the bottom line of

the LCD screen, as shown in Figure 64. Press the

Set Button

F

to enter the main EzSet menu

branch.

Figure 64

3. At the next menu screen (Figure 65) press the

⁄

/

¤

Navigation Buttons

n

once so that

EZSET DISABLE

appears in the lower line of

the LCD display.

Figure 65

4. Within five seconds, press the

Set Button

F

to

disable the

SPL Select Button

Á

. Once the

Set Button

F

is pressed the word

EXITING

will flash four times in the lower line of the LCD

display and then it will return to normal operation.

Once these steps are completed, when the

SPL

Select Button

Á

is pressed the remote will show

EZSET DISABLE

and it will not be activated.

To restore the EzSet feature to normal operation,

repeat the procedure outlined above, except that in

step #3 you should press the

⁄

/

¤

Navigation

Buttons

n

so that

EZSET ENABLE

appears in

the lower line of the LCD display. When that display

appears, press the

Set Button

F

and the EzSet

feature will be reactivated. You may then press the

Clear Button

9

to exit the remote’s menu system

and return to normal operation or press the

Set

Button

F

again to immediately use the EzSet

feature to calibrate the system as shown on pages

22 and 23.

Renaming

While the names given to the buttons and inputs on

the DPR represent recognizable categories of audio/

video products, system operation may be easier if the

displays shown in the remote’s LCD screen are cus-

tomized to reflect the specific characteristics of a play-

back source’s brand name or the new function given

to a specific button when one remote’s controls are

programmed into the DPR remote. The DPR remote

allows you to change the name of either a master

device or any button on the remote using the following

steps.

Renaming a Device

To rename a specific device/input source button, fol-

low these steps. For this example, we will show you

how to rename the Device/Input Selector normally

shown as “TV” to “HDTV TUNER.”

1. Press and hold the

Program Button

O

for

about three seconds while the message shown

in Figure 15 appears in the remote’s

LCD

Information Display

2

. Release the button

when the red light under the

Set Button

F

appears.

2.

The remote’s

MAIN MENU

message (Figure 16),

will appear in the LCD display and the

Set Button

F

will remain illuminated in red. Press the

⁄

/

¤

Navigation Buttons

n

until

RENAME

appears on the bottom line of the LCD screen, as

shown in Figure 66.

Figure 66

3. At the next menu screen press the

⁄

/

¤

Navigation Buttons

n

until

RENAME

DEVICE

appears on the bottom line of the

LCD screen, as shown in Figure 67. Press the

Set Button

F

to begin renaming a device.

Figure 67

4. The next display screen (Figure 68) is where you

select the device that will be renamed. In our

example, that is the TV button. Press the

⁄

/

¤

Navigation Buttons

n

until the name of the

base device appears and then press the

Set

Button

F

.

Figure 68

5. At the next menu screen you will see the device

name on the bottom line of the display with a

blinking cursor box to the right of the device

name. Press the

‹

Navigation Button

n

to

return the blinking cursor to the far left side of the

display line. You may then retitle the device name

as shown in the next step.

6. To enter the new name, press the

Numeric Keys

A

. The letters above the numbered buttons

indicate which letter or symbol will appear when

the button is pressed during the renaming

process. The first press of the button will enter the

first letter shown, subsequent presses of the same

button will change the display to the other letters

above that numbered key. For example, since the

first letter we need to rename the input to HDTV

Tuner is an “H”, you would locate the “H” above

the “4” button, and press the button twice. The

first press shows a “G,” the second press changes

it to an “H.” Consult the table at the end of this

section to see which characters pressing a

particular button generates.

7. After you enter the first letter of the new device

name, there are three options for entering the next

character:

a. To enter a letter that requires a different

numeric key to be pressed, simply press that

button. The cursor will automatically move to

the next position and the first letter accessed

RENAME DEVICE

TV

RENAME

RENAME DEVICE

MAIN MENU

RENAME

SET SPKR LEVELS

EZSET DISABLE

MAIN MENU

SET SPKR LEVELS

PUNCH-THROUGH

TV

<

-TV

CONFIGURING THE REMOTE

Harman Kardon DPR 1001 Owners Manual - Page 39

EzSet Configuration, Renaming

Page 39 highlights