Hayward AquaRite w/TurboCell for Pools up to 25 000 Gallons AquaRite-Electroni - Page 8

Controls, Main Switch, Indicator LED's

Get Hayward AquaRite w/TurboCell for Pools up to 25 000 Gallons PDF manuals and user guides View all Hayward AquaRite w/TurboCell for Pools up to 25 000 Gallons manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

Controls Main Switch AUTO: For normal operation, the Main Switch should be left in the AUTO position. In this position the AquaRite will produce chlorine according to the "Desired Output %" adjustment setting for the entire filtering/pumping cycle. SUPER CHLORINATE: When you have an abnormally high bather load, a large amount of rain, a cloudy water condition, or any other condition which needs a large amount of purification to be introduced, put the Main Switch in the SUPER CHLORINATE position. This electronically "super chlorinates" (shocks) the water for 24 hours (filter pump must be on during this time) or until the power has been turned off, whichever comes first. At the end of the super chlorinate time, be sure to put the switch back into the AUTO position. OFF: The OFF position prevents the AquaRite from energizing the electrolytic cell. In this position there is no chlorine generation. NOTE: To service any of the pool equipment or the AquaRite, turn the power off at the circuit breaker. Indicator LED's POWER When illuminated, the AquaRite has input power. GENERATING This LED is on steady during normal operation. When flashing, the pool water is too hot or cold to operate. SUPER CHLORINATE Illuminates during super-chlorination. See description above. REMOTELY CONTROLLED When illuminated, indicates that a remote pool automation control (Hayward Pro Logic, Pentair Intellitouch, Polaris Eos, etc.) is controlling the AquaRite--the main switch and "Desired Output %" adjustment are inactive. When flashing, the Pro Logic, Intellitouch or Eos is in SERVICE or TIME-OUT mode and the Main Switch and "Desired Output %" adjustment are active. NO FLOW When illuminated, the flow switch has detected no water flowing and the AquaRite has stopped generating chlorine. A flashing LED indicates a 15-60 second time delay period. CHECK SALT When flashing, the salt level is low (below 2700 ppm) and AquaRite is generating at low efficiency. When illuminated steady, the salt level is too low and AquaRite has shut down. Before adding large quantities of salt, it is advisable to have your salt level professionally checked. HIGH SALT When illuminated, the salt level is too high and AquaRite has shut down. INSPECT CELL A flashing indicator signifies that either the cell efficiency is reduced or that it is time for regularly scheduled cell inspection. In either case, inspect cell and clean if necessary. When illuminated steady, cell efficiency is greatly reduced and the AquaRite has stopped producing chlorine. Inspect, clean or replace if necessary. 7 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
Controls
Main Switch
AUTO:
For normal operation, the Main Switch should be left in the AUTO position.
In this position
the AquaRite will produce chlorine according to the "Desired Output %" adjustment setting for
the entire filtering/pumping cycle.
SUPER CHLORINATE:
When you have an abnormally high bather load, a large amount of rain,
a cloudy water condition, or any other condition which needs a large amount of purification to be
introduced, put the Main Switch in the SUPER CHLORINATE position.
This electronically “super
chlorinates” (shocks) the water for 24 hours (filter pump must be on during this time) or until the
power has been turned off, whichever comes first.
At the end of the super chlorinate time, be
sure to put the switch back into the AUTO position.
OFF:
The OFF position prevents the AquaRite from energizing the electrolytic cell.
In this position
there is no chlorine generation.
NOTE:
To service any of the pool equipment or the AquaRite,
turn the power off at the circuit breaker.
Indicator LED's
POWER
When illuminated, the AquaRite has input power.
GENERATING
This LED is on steady during normal operation.
When flashing, the pool water is
too hot or cold to operate.
SUPER CHLORINATE
Illuminates during super-chlorination.
See description above.
REMOTELY CONTROLLED
When illuminated, indicates that a remote pool automation control
(Hayward Pro Logic, Pentair Intellitouch, Polaris Eos, etc.) is controlling the AquaRite--the main
switch and "Desired Output %" adjustment are inactive.
When flashing, the Pro Logic, Intel-
litouch or Eos is in SERVICE or TIME-OUT mode and the Main Switch and "Desired Output %"
adjustment are active.
NO FLOW
When illuminated, the flow switch has detected no water flowing and the AquaRite
has stopped generating chlorine.
A flashing LED indicates a 15-60 second time delay period.
CHECK SALT
When flashing, the salt level is low (below 2700 ppm) and AquaRite is generating
at low efficiency.
When illuminated steady, the salt level is too low and AquaRite has shut down.
Before adding large quantities of salt, it is advisable to have your salt level professionally checked.
HIGH SALT
When illuminated, the salt level is too high and AquaRite has shut down.
INSPECT CELL
A flashing indicator signifies that either the cell efficiency is reduced or that it is
time for regularly scheduled cell inspection.
In either case, inspect cell and clean if necessary.
When illuminated steady, cell efficiency is greatly reduced and the AquaRite
has stopped producing
chlorine.
Inspect, clean or replace if necessary.
7
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS