Hayward PL-PLUS Operation Manual - Page 11
Settings Menu - series 2
View all Hayward PL-PLUS manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 11 highlights
The Aqua Plus 16v's six main menus have many items in each that allow you to customize the operation of your pool/spa equipment. The chart on the previous page shows the Aqua Plus 16v's six menus as well as each menu's specific settings. The Default Menu is a series of informative displays (temperatures, salt levels, chlorinator settings, etc.) with nothing to set. The Aqua Plus 16v will automatically switch to the default menu when no keys have been pressed for 2 minutes and will then scroll through each display. The Settings Menu and the Timers Menu are the menus you will be using most often to adjust the operation of your pool. The Configuration Menu is used when the system is installed and defines what equipment is connected to each output and the operational logic that will control the equipment. This menu is normally "locked" and should only be used by a pool professional. Details regarding the Configuration menu can be found on page 17. The "Diagnostic Menu" is primarily intended for the service technician and contains information and details about the system operation that are helpful in troubleshooting, if problems occur. The "Maintenance Menu" will be displayed only if the optional AQL-CHEM is used and the Sensing System is enabled in the Chemistry Config. Wizard. This menu is used to perform functions relating to the AQL-CHEM ORP and pH sensing kit. Settings Menu The Settings Menu allows you to set all system operating parameters except the timeclock and countdown timers which are part of the Timers Menu. ! Important: All of the displays shown below use the default generic names for each function or output. The Aqua Plus 16v allows more descriptive names to be assigned to each piece of equipment (refer to the section regarding the Configuration Menu for more information). Spa Heater1 Off not shown if Pool and Spa-Dual with separate heaters is selected Spa Heater2 102°F Adjust the desired spa temperature (Off, 65°F, 66°F, ...103°F, 104°F, Off) Move to previous/next menu item Adjust the desired spa temperature (Off, 65°F, 66°F, ...103°F, 104°F, Off) Move to previous/next menu item The spa heater setting will only appear if the system has been setup for "spa only" or "pool and spa" operation and the "Heater1" and/or "Heater2" control is enabled. The heater will turn on whenever the pool/spa valves are in the "spa only" position and the filter pump is running and the spa water temperature is less than the desired temperature setting. If you have both solar heat and a conventional heater and the solar priority option is selected (Configuration Menu), then the conventional heater will only operate when solar heat is NOT available. For Pool and Spa dual equipment with separate heaters ("Pool and Spa -Dual" and "Htr1=Spa, Htr2=Pool" selected), Spa Heater1 is tied to the Spa Filter (AUX1). not shown if Pool and Spa-Dual with separate heaters is selected Pool Heater1 Off Adjust the desired pool temperature (Off, 65°F, 66°F, ...103°F, 104°F, Off) Move to previous/next menu item Pool Heater2 85°F Adjust the desired pool temperature (Off, 65°F, 66°F, ...103°F, 104°F, Off) Move to previous/next menu item The pool heater setting will only appear if the system has been setup for "pool only" or "pool and spa" operation and the "Heater1" and/or "Heater2" control is enabled. The heater will turn on whenever the pool/spa valves are in the "pool only" or "spa spillover" position and the filter pump is running and the pool water temperature is less than the desired temperature setting. If you have both solar heat and a conventional heater and the solar priority option is selected (Configuration Menu), then the conventional heater will only operate when solar heat is NOT available. For Pool and Spa dual equipment with separate heaters ("Pool and Spa -Dual" and "Htr1=Spa, Htr2=Pool" selected), Pool Heater2 is tied to the Pool Filter (FILTER). 8