Hayward PL-PLUS Operation Manual - Page 46

Instant Minerals if Chlor. Config. is set for Display Minerals.

Get Hayward PL-PLUS PDF manuals and user guides View all Hayward PL-PLUS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Instant Salt Press to load the "Instant Salt" into the averaged salt display 3200 PPM (+=save) Move to previous/next menu item This display will be shown only if the chlorinator is enabled. This display shows "Instant Salt" or "Instant Minerals" (if Chlor. Config. is set for "Display Minerals"). The "Instant Salt" is calculated based on the voltage, current (amps), and water temperature at the cell. This is different than the "average salt" value which is displayed as part of the default menu. There are a number of reasons why instant and average salt readings may differ. Some of these include salt having just been added to the pool and not yet thoroughly mixed, calcium buildup on the cell, and the cell aging. if AQL-CHEM is used pH 7.5 (On) ORP 700 mV (On) No function Move to previous/next menu item This display will be shown only if sensing is enabled. This display shows both pH and ORP levels/ status when chemistry sensing is enabled via the Chemistry Configuration Wizard (requires the use of AQL-CHEM Sensing Kit). The Aqua Plus 16v will refer to these levels to determine how much chlorine dispense to generate (ORP) and, if using an AQL-CHEM2 (pH). Refer to the AQL-CHEM manual for specific dispense kit, how information about tmheuscehleCvOel2soars acid well to as the recommended ranges. Flow Switch Flow No function Move to previous/next menu item This display will be shown only if the chlorinator is enabled. The current status of the flow switch is displayed. There is a short delay when transitioning from flow to no-flow and a longer delay on the transition from no-flow to flow. The delay time is displayed. 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
43
Instant Salt
3200 PPM (+=save)
Move to previous/next menu item
Press to load the “Instant Salt” into the averaged salt display
This display will be shown only if the chlorinator is enabled.
This display shows “Instant Salt” or
“Instant Minerals” (if Chlor. Config. is set for “Display Minerals”).
The “Instant Salt” is calculated
based on the voltage, current (amps), and water temperature at the cell.
This is different than the
“average salt” value which is displayed as part of the default menu.
There are a number of reasons
why instant and average salt readings may differ.
Some of these include salt having just been added
to the pool and not yet thoroughly mixed, calcium buildup on the cell, and the cell aging.
pH 7.5
(On)
ORP 700 mV
(On)
No function
Move to previous/next menu item
if AQL-CHEM is used
This display will be shown only if sensing is enabled.
This display shows both pH and ORP levels/
status when chemistry sensing is enabled via the Chemistry Configuration Wizard (requires the use of
AQL-CHEM Sensing
Kit).
The Aqua Plus 16v will refer to these levels to determine how much
chlorine to generate (ORP) and, if using an AQL-CHEM2 dispense kit, how much CO
2
or acid to
dispense (pH).
Refer to the AQL-CHEM manual for specific information about these levels as well as
the recommended ranges.
Flow Switch
Flow
No function
Move to previous/next menu item
This display will be shown only if the chlorinator is enabled.
The current status of the flow switch is
displayed.
There is a short delay when transitioning from flow to no-flow and a longer delay on the
transition from no-flow to flow.
The delay time is displayed.