Hayward Pro Logic Model: PL-PS-4 PL-PS-8 PL-PS-16 PL-PS-16V Operation - Page 12
Set the desired Spa Filter Speed 1 from the Spa Filter Lowest to Spa Filter Highest - 10
View all Hayward Pro Logic manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 12 highlights
0.0 (1.5) 3.3 (3.0) 6.7 13.3 (6.0) 10.0 (4.5) 16.7 (7.5) 20.0 (9.0) 23.3 (10.5) 26.7 (12.0) 0.0 (1.4) 3.2 (2.8) 6.3 12.7 (5.7) 9.5 (4.3) 15.8 (7.1) 19.0 (8.6) 22.2 (10.0) 25.3 (11.5) 0.0 (1.3) 3.0 12.0 (5.4) 9.0 (4.1) 15.0 (6.7) 18.0 (8.1) 21.0 (9.5) 0.0 (1.3) 2.8 (2.6) 5.7 (3.9) 8.5 14.2 (6.3) 19.8 (9.0) 22.7 (10.3) 28,000 30,000 32,000 34,000 36,000 38,000 40,000 (105000) (112500)(120000)(127500)(135000) (142500) (150000) Spa Heater2 Priority: 10 hours Adjust the desired priority interval (Never, 1hr, 2hrs, 3hrs ...22hrs, 23hrs, Always) Move to previous/next menu item The spa heater priority setting will only appear if the system has been setup for "spa only" or "pool and spa"and if priority has been enabled for Spa Heater2. Choose "Never", "Always" or a selectable time interval. If an interval is selected, only Spa Heater2 will run when there is a call for heat. After the interval expires, both heaters will be allowed to operate until the desired temperature has been reached. Pool Heater2 Priority: Never Adjust the desired priority interval (Never, 1hr, 2hrs, 3hrs ...22hrs, 23hrs, Always) Move to previous/next menu item The pool heater priority setting will only appear if the system has been setup for "pool only" or "pool and spa"and if priority has been enabled for Pool Heater2. Choose "Never", "Always" or a selectable time interval. If an interval is selected, only Pool Heater2 will run when there is a call for heat. After the interval expires, both heaters will be allowed to operate until the desired temperature has been reached. Spa Solar 102°F Adjust the desired spa temperature (Off, 65°F, 66°F, ...103°F, 104°F, Off) Move to previous/next menu item The spa solar setting will only appear if the system has been setup for "spa only" or "pool and spa" operation and the solar control is enabled. The solar system will turn on whenever the pool/spa valves are in the "spa only" position and the filter pump is running and the spa water temperature is less than the desired temperature setting and solar heat is available. 0.0 (1.2) 2.7 (2.4) 5.3 (3.6) 8.0 (4.8) 10.7 13.3 (6.0) 16.0 (7.2) 18.7 (8.5) 21.3 (9.7) 0.0 (1.2) 2.5 (2.3) 5.0 (3.4) 7.5 (4.5) 10.0 12.5 (5.6) 15.0 (6.8) 17.2 (8.0) 20.0 (9.1) 0.0 (1.1) 2.3 (2.1) 4.7 (3.2) 7.0 (4.2) 9.3 11.7 (5.2) 0.0 (1.0) 2.2 4.3 (2.0) 6.5 (2.9) (3.9) 8.7 10.8 (4.9) 0.0 (.91) 2.0 (1.8) 4.0 (2.7) 6.0 (3.6) 8.0 10.0 (4.5) POUNDS and (Kg) OF STABILIZER (CYANURIC ACID) NEEDED FOR 80 PPM 0.0 (.82) 1.8 (1.7) 3.7 (2.5) 5.5 (3.3) 7.4 9.2 (4.2) 0.0 (.77) 1.7 (1.5) 3.3 (2.3) 5.0 (3.0) 6.7 8.4 (3.8) 0.0 (.68) 1.5 3.0 (1.4) (2.0) 4.5 (2.7) 6.0 7.5 (3.4) 0.0 (.64) 1.4 2.7 (1.2) 4.0 (1.8) (2.4) 5.4 6.7 (3.0) 14.0 (6.4) 16.4 (7.4) 18.7 (8.5) (5.9) 13.0 15.2 (6.9) 26,000 (97500) (5.4) (5.0) 10.0 11.0 12.0 14.0 (6.4) 16.0 (7.3) 24,000 (90000) Gallons and (Liters) of Pool/Spa water 12.9 (5.9) 14.7 (6.7) 22,000 (82500) (4.5) 11.7 (5.3) 13.4 (6.1) 20,000 (75000) (2.2) 9.0 10.5 (4.8) 12.0 (5.4) 18,000 (67500) Pool Solar 88°F Adjust the desired pool temperature (Off, 65°F, 66°F, ...103°F, 104°F, Off) Move to previous/next menu item The pool solar heater setting will only appear if the system has been setup for "pool only" or "pool and spa" operation and the solar control is enabled. The solar system will turn on whenever the pool/ spa valves are in the "pool only" or "spa spillover" position and the filter pump is running and the pool water temperature is less than the desired temperature setting and solar heat is available. only if an output is configured for a variable speed pump VSP Speed Settings Push to access Variable Speed Pump Speed Settings + to enter Move to previous/next configuration menu only if Filter is Variable Speed Filter Speed 1 Set the desired Filter Speed 1 from the Filter Lowest to the Filter Highest 95% Move to next menu item only if Pool and Spa-Dual and Spa Filter is Variable Speed Spa Filter Speed 1 Set the desired Spa Filter Speed 1 from the Spa Filter Lowest to Spa Filter Highest 95% Move to next menu item only if Pool and Spa-Std and Filter is Variable Speed Spa Speed 50% Move to next menu item only if Aux2 is controlled by a variable speed pump Aux2 Speed Set the desired Aux2 Speed from 10% to 100% 95% Move to next menu item The Filter, Dual Equipment Spa Filter, and up to 6 Lights and Aux outputs can be configured to control variable speed pumps. These settings allow you to select the desired speed of the variable speed pump for each output used. The speed can be displayed in % or RPM, whichever is selected in the Configuration Menu. For the Filter and Dual Equipment Spa Filter, when the output is on, the actual speed of the pump(s) will be dependent on the minimum and maximum speeds set for that output in the Configuration Menu. (3.6) 8.0 9.4 (4.3) 10.7 (4.9) 16,000 (60000) (3.2) 7.0 8.2 (3.7) 9.4 (4.3) 14,000 (52500) (2.7) 6.0 7.0 (3.2) 8.0 (3.6) 12,000 (45000) 5.8 (3.7) 6.7 (4.3) 10,000 (37500) 4.0 (2.7) 4.7 (3.2) 5.3 (3.6) 8,000 (30000) 30 ppm 20 ppm 10 ppm 0 ppm Current Stabilizer Level (ppm) Super Chlorinate Off Turn super chlorinate on or off Move to previous/next menu item This display only appears if the chlorinator function is enabled. If an AQL-CHEM is being used, super chlorinate will not be available if chemical sensing is enabled and ORP is in Auto Sensing (see AQLCHEM manual). 9 38 0.0 (.54) 1.2 2.3 (1.1) 3.5 (1.6) (2.1) 4.7 5.9 (2.7) 0.0 (.45) 1.0 2.0 (.91) 3.0 (1.4) (1.8) 4.0 5.0 (2.3) 0.0 (.54) 0.8 1.7 (1.1) 2.5 (1.6) (2.1) 3.3 4.2 (2.7) 80 ppm 0.0 (.45) 70 ppm 0.7 1.3 (.91) 2.0 (1.4) (1.8) 60 ppm 50 ppm 40 ppm 2.7 3.3 (2.3)