HP 10636 HP 10000 G2 Series Rack Options Installation Guide - Page 108

Install the bottom assembly of the rear extension assembly., Using a T-25 Torx driver

Get HP 10636 PDF manuals and user guides View all HP 10636 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 108 highlights

a. Align the top assembly with the installed side assemblies (1). b. Using a T-25 Torx driver, insert and tighten two M6 machine screws into the rear screw holes (2). c. Using a T-25 Torx driver, insert and tighten two M6 machine screws into the front screw holes (3). 3. Install the bottom assembly of the rear extension assembly. a. Align the bottom assembly with the installed side assemblies (1), making sure to set the metal tab at the front of the assembly over the rear rack frame (2). b. Using a T-25 Torx driver, insert and tighten four M6 machine screws into each corner hole (3). Rear Extension kit 108

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
Rear Extension kit 108
a.
Align the top assembly with the installed side assemblies (1).
b.
Using a T-25 Torx driver, insert and tighten two M6 machine screws into the rear screw holes (2).
c.
Using a T-25 Torx driver, insert and tighten two M6 machine screws into the front screw holes (3).
3.
Install the bottom assembly of the rear extension assembly.
a.
Align the bottom assembly with the installed side assemblies (1), making sure to set the metal tab at
the front of the assembly over the rear rack frame (2).
b.
Using a T-25 Torx driver, insert and tighten four M6 machine screws into each corner hole (3).