HP 14-w000 14 Notebook PC Maintenance and Service Guide - Page 60

Optical drive connector cable, Keyboard see

Get HP 14-w000 PDF manuals and user guides View all HP 14-w000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

4. Remove the TouchPad button board while carefully lifting the cable from the guides (3) (the cable was disconnected when removing the top cover). Reverse this procedure to install the TouchPad button board. Optical drive connector cable Before removing the optical drive connector cable, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4. Remove the battery (see Battery on page 25), and then remove the following components: a. Service door (see Service door on page 26) b. Memory module (see Memory module on page 28) c. WLAN module (see WLAN module on page 30) d. Optical drive (see Optical drive on page 32) e. Keyboard (see Keyboard on page 34) f. Top cover (see Top cover on page 41) Remove the optical drive connector cable: 1. Disconnect the optical drive connector cable (1) from the system board. 2. Release the optical drive connector cable from the clip (2) built into the base enclosure. 50 Chapter 6 Removal and replacement procedures for Authorized Service Provider parts

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
4.
Remove the TouchPad button board while carefully lifting the cable from the guides
(3)
(the cable was
disconnected when removing the top cover).
Reverse this procedure to install the TouchPad button board.
Optical drive connector cable
Before removing the optical drive connector cable, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the battery (see
Battery
on page
25
), and then remove the following components:
a.
Service door (see
Service door
on page
26
)
b.
Memory module (see
Memory module
on page
28
)
c.
WLAN module (see
WLAN module
on page
30
)
d.
Optical drive (see
Optical drive
on page
32
)
e.
Keyboard (see
Keyboard
on page
34
)
f.
Top cover (see
Top cover
on page
41
)
Remove the optical drive connector cable:
1.
Disconnect the optical drive connector cable
(1)
from the system board.
2.
Release the optical drive connector cable from the clip
(2)
built into the base enclosure.
50
Chapter 6
Removal and replacement procedures for Authorized Service Provider parts