HP 9250c HP 9250C Digital Sender - User Guide - Page 33

Menu item, Sub-menu item, Values and Description, Ping Test, Dest Type, Dest IP, Packet Size, Timeout - setup

Get HP 9250c - Digital Sender PDF manuals and user guides
UPC - 882780801028
View all HP 9250c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

Table 2-3 Jetdirect sub-menus (continued) Menu item Sub-menu item Ping Test Sub-menu item Dest Type Dest IP Packet Size Timeout Count Show Results Execute Values and Description This test is used to check network communications. This test sends link-level packets to a remote network host, then waits for an appropriate response. To run a ping test, set the following items: Specify whether the target device is an IPv4 or IPv6 node. IPV4: Type the IPv4 address. IPV6: Type the IPv6 address. Specify the size of each packet, in bytes, to be sent to the remote host. The minimum is 64 (default) and the maximum is 2048. Specify the length of time, in seconds, to wait for a response from the remote host. The default is 1 and the maximum is 100. Specify the number of ping test packets to send for this test. Select a value from 1 to 100. To configure the test to run continuously, select 0. If the ping test was not set for continuous operation, you can choose to display the test results. Select Yes to show results. If you select No (default), results are not shown. Specify whether to initiate the ping test. Select Yes to initiate the test, or No to not run the test. ENWW Initial Setup menu 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
Menu item
Sub-menu item
Sub-menu item
Values and Description
Ping Test
This test is used to check network communications.
This test sends link-level packets to a remote network
host, then waits for an appropriate response. To run a
ping test, set the following items:
Dest Type
Specify whether the target device is an IPv4 or IPv6
node.
Dest IP
IPV4
: Type the IPv4 address.
IPV6
: Type the IPv6 address.
Packet Size
Specify the size of each packet, in bytes, to be sent to
the remote host. The minimum is 64 (default) and the
maximum is 2048.
Timeout
Specify the length of time, in seconds, to wait for a
response from the remote host. The default is 1 and
the maximum is 100.
Count
Specify the number of ping test packets to send for this
test. Select a value from 1 to 100. To configure the test
to run continuously, select 0.
Show Results
If the ping test was not set for continuous operation,
you can choose to display the test results. Select
Yes
to show results. If you select
No
(default), results are
not shown.
Execute
Specify whether to initiate the ping test. Select
Yes
to
initiate the test, or
No
to not run the test.
Table 2-3
Jetdirect sub-menus (continued)
ENWW
Initial Setup menu
25