HP BL2x220c HP ProLiant BL2x220c Generation 5 Server Blade Maintenance and Ser - Page 25

Install server B assembly, Hard drive

Page 25 highlights

5. Turn jackscrew 1 approximately six turns counterclockwise. 6. Turn jackscrew 2 counterclockwise until the threads are fully disengaged. 7. Turn jackscrew 1 counterclockwise until the threads are fully disengaged. CAUTION: To prevent damage to the server blade, do not apply pressure to the enclosure connector. 8. Lift server B assembly from server A assembly, and then place it on the work surface with the system board facing up. Install server B assembly For access component identification, see "Access components (on page 59)." 1. Extend the server B serial label pull tab. 2. Engage the front edge of server B assembly with the front edge of server A assembly. CAUTION: Route the cache module battery cables so that they do not become pinched when the server B assembly is installed. 3. Lower server B assembly onto server A assembly. 4. Align the signal and power connectors on server B assembly with the corresponding connectors on server A assembly. CAUTION: The jackscrews control the unseating and seating of critical system connectors. Failure to use the jackscrews to remove and install the server B assembly can cause the system boards to fail. 5. Engage the threads on jackscrew 1 and tighten six turns clockwise. 6. Engage the threads on jackscrew 2 and tighten fully. 7. Tighten jackscrew 1 fully. Hard drive Removal and replacement procedures 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68

Removal and replacement procedures
25
5.
Turn jackscrew 1 approximately six turns counterclockwise.
6.
Turn jackscrew 2 counterclockwise until the threads are fully disengaged.
7.
Turn jackscrew 1 counterclockwise until the threads are fully disengaged.
CAUTION:
To prevent damage to the server blade, do not apply pressure to the enclosure
connector.
8.
Lift server B assembly from server A assembly, and then place it on the work surface with the system
board facing up.
Install server B assembly
For access component identification, see "Access components (on page
59
)."
1.
Extend the server B serial label pull tab.
2.
Engage the front edge of server B assembly with the front edge of server A assembly.
CAUTION:
Route the cache module battery cables so that they do not become pinched when
the server B assembly is installed.
3.
Lower server B assembly onto server A assembly.
4.
Align the signal and power connectors on server B assembly with the corresponding connectors on
server A assembly.
CAUTION:
The jackscrews control the unseating and seating of critical system connectors.
Failure to use the jackscrews to remove and install the server B assembly can cause the system
boards to fail.
5.
Engage the threads on jackscrew 1 and tighten six turns clockwise.
6.
Engage the threads on jackscrew 2 and tighten fully.
7.
Tighten jackscrew 1 fully.
Hard drive