HP BL2x220c HP ProLiant BL2x220c Generation 5 Server Blade Maintenance and Ser - Page 36

Mezzanine card

Get HP BL2x220c - ProLiant - G5 Server A PDF manuals and user guides View all HP BL2x220c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

4. Disconnect the battery cables from the battery packs. 5. Do one of the following: o If a heatsink blank is installed on processor socket 2, remove the heatsink blank and then remove the cables from between the processor socket and the chassis. o If a processor and heatsink are installed in processor socket 2, remove the server A system board assembly ("Server A system board" on page 37) and then remove the cables from between the system board and heatsink. 6. Remove the cable from the cable clips. 7. Remove the cable shield from the upper mezzanine card thumbscrew and the signal connector. 8. Disconnect the cable from the upper cache module. 9. Remove the upper mezzanine card ("Mezzanine card" on page 36). 10. Disconnect the remaining cable from the lower cache module. 11. Remove the lower mezzanine card ("Mezzanine card" on page 36). 12. Remove the failed cable. CAUTION: To prevent battery cable and system board damage, always install the cable shield. To replace the component, reverse the removal procedure. Mezzanine card To remove the component: 1. Power down the server blade (on page 23). 2. Remove the server blade (on page 23). 3. Access the internal server components (on page 24). 4. Disconnect any cables connected to the mezzanine card. Removal and replacement procedures 36

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
Removal and replacement procedures
36
4.
Disconnect the battery cables from the battery packs.
5.
Do one of the following:
o
If a heatsink blank is installed on processor socket 2, remove the heatsink blank and then remove
the cables from between the processor socket and the chassis.
o
If a processor and heatsink are installed in processor socket 2, remove the server A system board
assembly ("
Server A system board
" on page
37
) and then remove the cables from between the
system board and heatsink.
6.
Remove the cable from the cable clips.
7.
Remove the cable shield from the upper mezzanine card thumbscrew and the signal connector.
8.
Disconnect the cable from the upper cache module.
9.
Remove the upper mezzanine card ("
Mezzanine card
" on page
36
).
10.
Disconnect the remaining cable from the lower cache module.
11.
Remove the lower mezzanine card ("
Mezzanine card
" on page
36
).
12.
Remove the failed cable.
CAUTION:
To prevent battery cable and system board damage, always install the cable
shield.
To replace the component, reverse the removal procedure.
Mezzanine card
To remove the component:
1.
Power down the server blade (on page
23
).
2.
Remove the server blade (on page
23
).
3.
Access the internal server components (on page
24
).
4.
Disconnect any cables connected to the mezzanine card.