HP D2D HP StorageWorks Linux and UNIX configuration guide for D2D Backup Syste - Page 43

Solaris (x86 and SPARC), Overview, Configuring the HP D2D Backup System for iSCSI, How to enable - default password

Get HP D2D PDF manuals and user guides View all HP D2D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

5 Solaris (x86 and SPARC) Overview This chapter describes how to configure the HP D2D Backup System for use with the following Solaris operating systems: • Solaris 9 (SPARC) • Solaris 10 (x86 and SPARC) NOTE: HP StorageWorks D2D Backup Systems with iSCSI interfaces are only supported with Solaris 10u4 or greater. Configuring the HP D2D Backup System for iSCSI How to enable the iSCSI software initiator 1. Enable the iSCSI services using the command: # svcadm -v enable iscsi_initiator svc:/network/iscsi_initiator:default enabled 2. Verify the iSCSI services are running: # svcs -a | grep iscsi_initiator Online 10:10:28 svc: /network/iscsi_initiator:default How to configure the iSCSI software initiator using the D2Dsetup script Use the D2Dsetup script to configure the iSCSI software initiator automatically. You must provide the IP address as a parameter to the script. # D2Dsetup If you wish to configure CHAP authentication, you should also provide the user name and password for the initiator and the target, if required. # D2Dsetup The response from the HP D2D Backup System will be similar to the following: HP StorageWorks D2D Backup System Linux and UNIX iSCSI Configuration Tool Detecting OS done Checking iSCSI package done Contacting HP StorageWorks D2D Backup System...done Discovering available targets done D2D Backup System 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
5 Solaris (x86 and SPARC)
Overview
This chapter describes how to configure the HP D2D Backup System for use with the following Solaris
operating systems:
•
Solaris 9 (SPARC)
•
Solaris 10 (x86 and SPARC)
NOTE:
HP StorageWorks D2D Backup Systems with iSCSI interfaces are only supported with Solaris 10u4
or greater.
Configuring the HP D2D Backup System for iSCSI
How to enable the iSCSI software initiator
1.
Enable the iSCSI services using the command:
# svcadm –v enable iscsi_initiator
svc:/network/iscsi_initiator:default enabled
2.
Verify the iSCSI services are running:
# svcs –a | grep iscsi_initiator
Online
10:10:28 svc: /network/iscsi_initiator:default
How to configure the iSCSI software initiator using the D2Dsetup script
Use the D2Dsetup script to configure the iSCSI software initiator automatically. You must provide the
IP address as a parameter to the script.
# D2Dsetup <IP_address>
If you wish to configure CHAP authentication, you should also provide the user name and password
for the initiator and the target, if required.
# D2Dsetup <Initiator_CHAP_Username> <Initiator_CHAP_Password>
<Target_CHAP_Username> <Target_CHAP_Password> <IP_address>
The response from the HP D2D Backup System will be similar to the following:
HP StorageWorks D2D Backup System Linux and UNIX iSCSI Configuration Tool
Detecting OS
...................................
done
Checking iSCSI package
.........................
done
Contacting HP StorageWorks D2D Backup System...done
Discovering available targets
..................
done
D2D Backup System
43