HP Designjet 5100 HP Designjet 5100 Printer Series - Users Guide - Page 71

Front-panel messages - printer specifications

Get HP Designjet 5100 PDF manuals and user guides View all HP Designjet 5100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

Front-panel messages Front-panel messages Status A factory media cannot be deleted. Calibrate error Calibration cancelled Calibration Error XXXX Press Enter to Continue Cancelling firmware upgrade. Please wait. Delete media profile? Edge not found. Reload media. Full ink cartridges needed Have ink tube replaced or risk printer damage Contact HP Description Procedure You cannot delete this printing material because it is one of the standard materials that was added in the factory. The calibration the printer was performing has failed. Note down the calibration error code that comes with this message, and which calibration failed, and contact your support representative. The printer was performing a calibration and you pressed the CANCEL key on the front panel. If the printer was performing a calibration to correct an internal error the correct functioning of the printer may be affected. The printer was calibrating and failed to complete the calibration. The front panel shows an error code, represented here by XXXX. Press Enter to continue. You can continue to print; but, if the printer was performing a calibration to correct an internal error, the correct functioning of the printer may be affected. You are downloading new firmware and the action has been canceled. This may be because the firmware/ software you are attempting to download is older than the version you already have, or the version is not compatible with your printer. You are about to delete the profile that you have in the printer for a specific printing material. The internal sensor on the carriage cannot see the edge of the printing material. This may be because the material is 100% transparent or because the lens cover is dirty. Try to load a different printing material. If the same message is displayed, replace the lens cover. See the "Using Your Printer" CD. The ink system startup must have full cartridges to enable the initialization of the complete ink system. Remove the ink cartridges that are low on ink and replace with full ink cartridges. The internal ink system tubes need replacing urgently. The ink system tubes have reached the end of their useful life. Please replace them before they break and damage the printer. HP Designjet 5100 printer Customer Reference Guide 5-3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
5-3
Front-panel messages
HP Designjet 5100 printer Customer Reference Guide
Front-panel messages
Status
Description
Procedure
A factory media
cannot be deleted.
You cannot delete this printing
material because it is one of
the standard materials that
was added in the factory.
Calibrate error
The calibration the printer was
performing has failed.
Note down the calibration error code
that comes with this message, and
which calibration failed, and contact
your support representative.
Calibration
cancelled
The printer was performing a
calibration and you pressed
the CANCEL key on the front
panel.
If the printer was performing a
calibration to correct an internal error
the correct functioning of the printer
may be affected.
Calibration Error
XXXX
Press
Enter
to
Continue
The printer was calibrating
and failed to complete the
calibration. The front panel
shows an error code,
represented here by XXXX.
Press
Enter
to continue. You can
continue to print; but, if the printer was
performing a calibration to correct an
internal error, the correct functioning of
the printer may be affected.
Cancelling
firmware upgrade.
Please wait.
You are downloading new
firmware and the action has
been canceled.
This may be because the firmware/
software you are attempting to
download is older than the version
you already have, or the version is not
compatible with your printer.
Delete media
profile?
You are about to delete the
profile that you have in the
printer for a specific printing
material.
Edge not found.
Reload media.
The internal sensor on the
carriage cannot see the edge
of the printing material. This
may be because the material
is 100% transparent or
because the lens cover is dirty.
Try to load a different printing
material. If the same message is
displayed, replace the lens cover.
See the “Using Your Printer” CD.
Full ink cartridges
needed
The ink system startup must
have full cartridges to enable
the initialization of the
complete ink system.
Remove the ink cartridges that are low
on ink and replace with full ink
cartridges.
Have ink tube
replaced or risk
printer damage
Contact HP
The internal ink system tubes
need replacing urgently.
The ink system tubes have reached the
end of their useful life. Please replace
them before they break and damage
the printer.