HP ENVY 13-ay0000 Maintenance and Service Guide - Page 43

Solid-state drive, Remove the Phillips M2.0×3.0 screw

Get HP ENVY 13-ay0000 PDF manuals and user guides View all HP ENVY 13-ay0000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

3. Disconnect the WLAN antenna cables (2) from the WLAN module terminals. NOTE: The #1/white WLAN antenna cable connects to the WLAN module #1/Main terminal. The #2/black WLAN antenna cable connects to the WLAN module #2/Aux terminal. 4. Remove the Phillips M2.0×3.0 screw (3) that secures the WLAN module to the system board. (The WLAN module tilts up.) 5. Remove the WLAN module (4) by pulling the module away from the slot at an angle. NOTE: WLAN modules are notched to prevent incorrect installation. Reverse this procedure to install the WLAN module. Solid-state drive Table 5-4 Solid-state drive spare part information Description 1 TB, M.2 2280, PCIe, NVMe-3×4, SS solid-state drive with TLC 1 TB, M.2 2280, PCIe, NVMe, value solid-state drive 512 GB, M.2 2280, PCIe-3×4, SS solid-state drive with TLC 512 GB, M.2 2280, PCIe, NVMe, value solid-state drive 256 GB, M.2 2280, PCIe-3×4, SS solid-state drive with TLC 256 GB, M.2 2280, PCIe, NVMe, value solid-state drive 128 GB, M.2 2280, PCIe, NVMe, solid-state drive with TLC Before removing the solid-state drive, follow these steps: Spare part number L85348-005 L85370-005 L85360-005 L85364-005 L85350-005 L85354-005 L90345-005 Component replacement procedures 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
3.
Disconnect the WLAN antenna cables
(2)
from the WLAN module terminals.
NOTE:
The #1/white WLAN antenna cable connects to the WLAN module
#1/Main
terminal. The #2/black
WLAN antenna cable connects to the WLAN module
#2/Aux
terminal.
4.
Remove the Phillips M2.0×3.0 screw
(3)
that secures the WLAN module to the system board.
(The WLAN module tilts up.)
5.
Remove the WLAN module
(4)
by pulling the module away from the slot at an angle.
NOTE:
WLAN modules are notched to prevent incorrect installation.
Reverse this procedure to install the WLAN module.
Solid-state drive
Table 5-4
Solid-state drive spare part information
Description
Spare part number
1 TB, M.2 2280, PCIe, NVMe-3×4, SS solid-state drive with TLC
L85348-005
1 TB, M.2 2280, PCIe, NVMe, value solid-state drive
L85370-005
512 GB, M.2 2280, PCIe-3×4, SS solid-state drive with TLC
L85360-005
512 GB, M.2 2280, PCIe, NVMe, value solid-state drive
L85364-005
256 GB, M.2 2280, PCIe-3×4, SS solid-state drive with TLC
L85350-005
256 GB, M.2 2280, PCIe, NVMe, value solid-state drive
L85354-005
128 GB, M.2 2280, PCIe, NVMe, solid-state drive with TLC
L90345-005
Before removing the solid-state drive, follow these steps:
Component replacement procedures
35