HP ENVY 15-w000 Maintenance and Service Guide - Page 42

Solid-state drive (M.2), Remove the Phillips PM2.0×3.0 screw

Get HP ENVY 15-w000 PDF manuals and user guides View all HP ENVY 15-w000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

Solid-state drive (M.2) Description 256 GB solid-state drive (SSD), M.2, TLC Spare part number 813081-001 Before removing the solid-state drive, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4. Remove the top cover (see Top cover on page 27). 5. Disconnect the battery. Remove the solid-state drive: 1. Remove the Phillips PM2.0×3.0 screw (1) that secures the solid-state drive to the system board. 2. Remove the solid-state drive (2) by pulling the drive away from the slot at an angle. 32 Chapter 5 Removal and replacement procedures for Authorized Service Provider parts

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
Solid-state drive (M.2)
Description
Spare part number
256 GB solid-state drive (SSD), M.2, TLC
813081-001
Before removing the solid-state drive, follow these steps:
1.
Turn
off
the computer. If you are unsure whether the computer is
off
or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the top cover (see
Top cover
on page
27
).
5.
Disconnect the battery.
Remove the solid-state drive:
1.
Remove the Phillips PM2.0×3.0 screw
(1)
that secures the solid-state drive to the system board.
2.
Remove the solid-state drive
(2)
by pulling the drive away from the slot at an angle.
32
Chapter 5
Removal and replacement procedures for Authorized Service Provider parts