HP ENVY 15-w000 Maintenance and Service Guide - Page 50

Speaker cable, Battery cable

Get HP ENVY 15-w000 PDF manuals and user guides View all HP ENVY 15-w000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

3. Disconnect all external devices from the computer. 4. Remove the top cover (see Top cover on page 27). NOTE: When replacing the system board, be sure that the following components (as applicable) are removed from the defective system board and installed on the replacement system board: ● WLAN module (see WLAN module on page 34) ● Solid-state drive (see Solid-state drive (M.2) on page 32) ● Memory modules (see Memory module on page 42) ● Heat sink (see Heat sink on page 44) Remove the system board: 1. Disconnect the following cables from the system board: (1): Display cable (2): Touch board cable (3): USB/card reader board cable (4): Battery cable (5): Speaker cable (6): Power connector cable 2. Remove the two Phillips PM2.5×4.0 screws that secure the system board to the computer (1). 3. Remove the two Phillips PM2.5×4.0 screws (2) that secure the fan to the computer. 40 Chapter 5 Removal and replacement procedures for Authorized Service Provider parts

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
3.
Disconnect all external devices from the computer.
4.
Remove the top cover (see
Top cover
on page
27
).
NOTE:
When replacing the system board, be sure that the following components (as applicable) are
removed from the defective system board and installed on the replacement system board:
●
WLAN module (see
WLAN module
on page
34
)
●
Solid-state drive (see
Solid-state drive (M.2)
on page
32
)
●
Memory modules (see
Memory module
on page
42
)
●
Heat sink (see
Heat sink
on page
44
)
Remove the system board:
1.
Disconnect the following cables from the system board:
(1):
Display cable
(2):
Touch board cable
(3):
USB/card reader board cable
(4):
Battery cable
(5):
Speaker cable
(6):
Power connector cable
2.
Remove the two Phillips PM2.5×4.0 screws that secure the system board to the computer
(1)
.
3.
Remove the two Phillips PM2.5×4.0 screws
(2)
that secure the fan to the computer.
40
Chapter 5
Removal and replacement procedures for Authorized Service Provider parts