HP ENVY m6-n113dx HP ENVY m6 Notebook PC HP ENVY Notebook PC Maintenance and S - Page 61

Disconnect the the webcam/microphone module cable, from the system board.

Get HP ENVY m6-n113dx PDF manuals and user guides View all HP ENVY m6-n113dx manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

6. Remove the hard drive (see Hard drive on page 42). 7. Remove the base enclosure (see Base enclosure on page 49). Remove the display assembly: 1. Release the wireless antenna cables from the retention clips built into the left rear speaker (1), connector board (2), and top cover (3). 2. Release the wireless antenna cables from the retention clips (4) built into the subwoofer. 3. Release the ZIF connector to which the display panel cable is attached, and then disconnect the display panel cable (5) from the system board. 4. Disconnect the the webcam/microphone module cable (6) from the system board. 5. Release the display panel cable and the webcam/microphone module cable from the clips and routing channel built into the right rear speaker (7). 6. Remove the three Phillips PM2.5×4.5 screws (1) (two on the left hinge, one on the right hinge) that secure the display assembly to the top cover. Component replacement procedures 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
6.
Remove the hard drive (see
Hard drive
on page
42
).
7.
Remove the base enclosure (see
Base enclosure
on page
49
).
Remove the display assembly:
1.
Release the wireless antenna cables from the retention clips built into the left rear speaker
(1)
,
connector board
(2)
, and top cover
(3)
.
2.
Release the wireless antenna cables from the retention clips
(4)
built into the subwoofer.
3.
Release the ZIF connector to which the display panel cable is attached, and then disconnect the
display panel cable
(5)
from the system board.
4.
Disconnect the the webcam/microphone module cable
(6)
from the system board.
5.
Release the display panel cable and the webcam/microphone module cable from the clips and
routing channel built into the right rear speaker
(7)
.
6.
Remove the three Phillips PM2.5×4.5 screws
(1)
(two on the left hinge, one on the right hinge)
that secure the display assembly to the top cover.
Component replacement procedures
53