HP EliteBook Revolve 810 EliteBook Revolve 810 G3 Maintenance and Service Guid - Page 62

Remove the Phillips PPM2.0×2.9 screw, Close the computer.

Get HP EliteBook Revolve 810 PDF manuals and user guides View all HP EliteBook Revolve 810 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

● RTC battery (see RTC battery on page 49) ● Fan/heat sink assembly (see Fan/heat sink assembly on page 53) Remove the system board: 1. Turn the computer right side up, with the front toward you. 2. Open the computer. 3. Release the ZIF connector (1) to which the TouchPad cable is attached, and then disconnect the TouchPad cable (2) from the system board. 4. Detach the TouchPad cable (3) from the bottom cover. (The TouchPad cable is attached to the bottom cover with double-sided tape.) 5. Close the computer. 6. Turn the computer upside down with the rear toward you. 7. Disconnect the display panel cable (1) from the system board. 8. Remove the Phillips PPM2.0×2.9 screw (2) and the Phillips PPM2.0×2.3 broad head screw (3) that secure the system board to the top cover. 52 Chapter 6 Removal and replacement procedures for Authorized Service Provider parts

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
●
RTC battery (see
RTC battery
on page
49
)
●
Fan/heat sink assembly (see
Fan/heat sink assembly
on page
53
)
Remove the system board:
1.
Turn the computer right side up, with the front toward you.
2.
Open the computer.
3.
Release the ZIF connector
(1)
to which the TouchPad cable is attached, and then disconnect
the TouchPad cable
(2)
from the system board.
4.
Detach the TouchPad cable
(3)
from the bottom cover. (The TouchPad cable is attached to the bottom
cover with double-sided tape.)
5.
Close the computer.
6.
Turn the computer upside down with the rear toward you.
7.
Disconnect the display panel cable
(1)
from the system board.
8.
Remove the Phillips PPM2.0×2.9 screw
(2)
and the Phillips PPM2.0×2.3 broad head screw
(3)
that
secure the system board to the top cover.
52
Chapter 6
Removal and replacement procedures for Authorized Service Provider parts