HP GbE2c HP GbE2c Ethernet Blade Switch for c-Class BladeSystem User Guide - Page 51

connect to the TFTP server, or after connection

Get HP GbE2c - Blc Layer 2/3 Fiber SFP Option PDF manuals and user guides
UPC - 808736802215
View all HP GbE2c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

• The management network address/mask (if used) does not contain the IP address of the management station. From the serial console interface, be sure that the management network address/mask contains the IP address of the management station. Cannot enable a port in multiple VLANs while configuring VLANS Action: A port is part of only one VLAN unless the port is a tagged port. Be sure that the port is enabled as a tagged port. The switch does not let the user enable two adjacent ports into two different VLANs while assigning the ports to VLANs Action: The ports are two adjacent ports that are bundled in a Port Trunk. Two ports that are assigned to a Port Trunk cannot be assigned to two different VLANs. Either break the trunk to assign it two different VLANs or assign the ports to one VLAN. While using TFTP to download firmware, the switch fails to connect to the TFTP server, or after connection the download fails Action: • The TFTP server is not available to connect to or there is connectivity failure between the switch and TFTP server. • Be sure that the IP address of the TFTP server is correct. • Be sure that the TFTP server exists on the same network and VLAN as the switch. • Be sure that the TFTP server can be pinged from the switch and vice versa. • The firmware file is not found on the TFTP server. The file name could be wrong. • Be sure that a valid firmware file exists on the TFTP server to download to the switch. • On the switch, check the file name configured to download. • The TFTP server was started with a configured directory. The switch must be configured using the full path name, if it is not in the directory specified in the TFTP server. The switch fails to connect to the TFTP server while using TFTP to download or upload a configuration file, or after connection the download or upload fails Action: • The TFTP server is not available to connect or there is a connectivity failure between the switch and the TFTP server. Troubleshooting 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
Troubleshooting 51
•
The management network address/mask (if used) does not contain the IP address of the
management station. From the serial console interface, be sure that the management network
address/mask contains the IP address of the management station.
Cannot enable a port in multiple VLANs while configuring
VLANS
Action:
A port is part of only one VLAN unless the port is a tagged port. Be sure that the port is enabled as a
tagged port.
The switch does not let the user enable two adjacent ports
into two different VLANs while assigning the ports to
VLANs
Action:
The ports are two adjacent ports that are bundled in a Port Trunk. Two ports that are assigned to a Port
Trunk cannot be assigned to two different VLANs. Either break the trunk to assign it two different VLANs
or assign the ports to one VLAN.
While using TFTP to download firmware, the switch fails to
connect to the TFTP server, or after connection the
download fails
Action:
•
The TFTP server is not available to connect to or there is connectivity failure between the switch and
TFTP server.
•
Be sure that the IP address of the TFTP server is correct.
•
Be sure that the TFTP server exists on the same network and VLAN as the switch.
•
Be sure that the TFTP server can be pinged from the switch and vice versa.
•
The firmware file is not found on the TFTP server. The file name could be wrong.
•
Be sure that a valid firmware file exists on the TFTP server to download to the switch.
•
On the switch, check the file name configured to download.
•
The TFTP server was started with a configured directory. The switch must be configured using the full
path name, if it is not in the directory specified in the TFTP server.
The switch fails to connect to the TFTP server while using
TFTP to download or upload a configuration file, or after
connection the download or upload fails
Action:
•
The TFTP server is not available to connect or there is a connectivity failure between the switch and
the TFTP server.