HP Integrity rx5670 Windows Integrity nPartition Guide - Page 156

Table 6-2, Application Event Log messages

Get HP Integrity rx5670 PDF manuals and user guides View all HP Integrity rx5670 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 156 highlights

Troubleshooting Error messages and corrective actions Table 6-2 Application Event Log messages Message Cause Recommended Action Operation failed. Firmware error. Service processor error. Request could not be completed. System firmware failed to perform the requested operation. MP firmware failed to perform requested operation. See additional information in AEL. The power-on request could not be satisfied because an N- power condition would result. The power-on request could not be satisfied because an insufficient cooling condition would result. There is insufficient system power to service a cell that was specified to be powered on. There is insufficient system cooling to service a cell that was specified to be powered on. Add additional power supplies or replace a defective power supply. Add additional fans or blower units or replace a defective fan or blower. Timed out waiting for a response. Insufficient privilege to perform the operation. Invalid user name. Operation is only supported by the local operating system. Datagram was lost. Requesting user does not have permission to perform the requested operation. Username specified in the request was not valid on the target nPartition. The requested operation can only be performed by a provider running on the nPartition. It cannot be performed through the MP. Retry command or use a management PC with a more reliable connection to the target MP or nPartition. Run the command as Administrator or "root". Use a valid username. Use the -u option with the command. Operation is not supported by the firmware. The system firmware does not support the requested operation. Cannot perform the request on this target system. May require updating the system firmware. 156 Chapter 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
Troubleshooting
Error messages and corrective actions
Chapter 6
156
Table 6-2
Application Event Log messages
Message
Cause
Recommended Action
Operation failed.
Request could not be
completed.
See additional information
in AEL.
Firmware error.
System firmware failed to
perform the requested
operation.
Service processor error.
MP firmware failed to
perform requested
operation.
The power-on request
could not be satisfied
because an N- power
condition would result.
There is insufficient
system power to service a
cell that was specified to
be powered on.
Add additional power
supplies or replace a
defective power supply.
The power-on request
could not be satisfied
because an insufficient
cooling condition would
result.
There is insufficient
system cooling to service a
cell that was specified to
be powered on.
Add additional fans or
blower units or replace a
defective fan or blower.
Timed out waiting for a
response.
Datagram was lost.
Retry command or use a
management PC with a
more reliable connection to
the target MP or
nPartition.
Insufficient privilege to
perform the operation.
Requesting user does not
have permission to
perform the requested
operation.
Run the command as
Administrator or “root”.
Invalid user name.
Username specified in the
request was not valid on
the target nPartition.
Use a valid username.
Operation is only
supported by the local
operating system.
The requested operation
can only be performed by a
provider running on the
nPartition. It cannot be
performed through the
MP.
Use the
-u
option with the
command.
Operation is not supported
by the firmware.
The system firmware does
not support the requested
operation.
Cannot perform the
request on this target
system. May require
updating the system
firmware.