HP Integrity rx6600 Rack to Pedestal Conversion Guide - HP Integrity rx6600 Se
HP Integrity rx6600 Manual
View all HP Integrity rx6600 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP Integrity rx6600 manual content summary:
- HP Integrity rx6600 | Rack to Pedestal Conversion Guide - HP Integrity rx6600 Se - Page 1
HP Integrity rx6600 Rack to Pedestal Conversion Guide HP Part Number: AB464-9009A Published: November 2006 Edition: 1 - HP Integrity rx6600 | Rack to Pedestal Conversion Guide - HP Integrity rx6600 Se - Page 2
© Copyright 2006 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be - HP Integrity rx6600 | Rack to Pedestal Conversion Guide - HP Integrity rx6600 Se - Page 3
the Caster Wheels...8 Pallet Installation Procedure...9 Floor Installation Procedure...13 Installing the Bezel Cover...14 Installing the Pedestal Kit Sides...15 Installing the Pedestal Kit Top...15 3 Pedestal to Rack Conversion 16 Required Tools...16 Powering Down the Server and Removing Cables 16 - HP Integrity rx6600 | Rack to Pedestal Conversion Guide - HP Integrity rx6600 Se - Page 4
on Pallet...9 2-2 Pallet Ramp...10 2-3 Raised Server...10 2-4 Caster Wheels on Raised Server...11 2-5 Ramp Attached to Pallet...12 2-6 Ramp Attachment Detail...13 2-7 Caster Wheels on the Server...14 2-8 Attaching the Bezel Cover...15 3-1 Server Rear...17 3-2 Lock Release Slot...18 3-3 Locking - HP Integrity rx6600 | Rack to Pedestal Conversion Guide - HP Integrity rx6600 Se - Page 5
This document is intended to provide technical product and support information for authorized service providers, customer system administrators, and HP support personnel. Document Organization The HP Integrity Rack to Tower Conversion Guide contains two chapters, and is organized as follows - HP Integrity rx6600 | Rack to Pedestal Conversion Guide - HP Integrity rx6600 Se - Page 6
. We are committed to providing documentation that meets your needs. Send any errors found, suggestions for improvement, or compliments to: [email protected] Include the document title, manufacturing part number, and any comment, error found, or suggestion for improvement you have concerning this - HP Integrity rx6600 | Rack to Pedestal Conversion Guide - HP Integrity rx6600 Se - Page 7
problem is relatively rare, it may be an issue within your computer room. Since metallic contamination can cause permanent or intermittent failures on your electronic equipment, Hewlett-Packard strongly recommends that your site be evaluated for metallic particulate contamination before installation - HP Integrity rx6600 | Rack to Pedestal Conversion Guide - HP Integrity rx6600 Se - Page 8
the front with the server in a horizontal orientation. Required Tools There are no tools required for installing the pedestal kit, but tools may be required to remove rack components from the server. See the Rack System /E User's Manual at: http://www.hp.com under Enterprise Rack & Power Products - HP Integrity rx6600 | Rack to Pedestal Conversion Guide - HP Integrity rx6600 Se - Page 9
, removing the accessory tray and pedestal kit box. 2. Unfold the bottom tray. See Figure 2-1 Figure 2-1 Server on Pallet 3 1 Side Bottom Foam Cushion (one on each side) 2 Front and Rear Bottom End Foam Cushions 3 Bottom Tray 3. Carefully, pull out the Side Bottom Foam Cushions from the right and - HP Integrity rx6600 | Rack to Pedestal Conversion Guide - HP Integrity rx6600 Se - Page 10
Figure 2-2 Pallet Ramp 1 Pallet Ramp 5. Raise the server, one side at a time, by lifting it up, and placing it on the Side Bottom Foam Cushions. See Figure 2-3. WARNING! Be careful when lifting the server as it is heavy. Figure 2-3 Raised Server 10 Rack to Pedestal Conversion - HP Integrity rx6600 | Rack to Pedestal Conversion Guide - HP Integrity rx6600 Se - Page 11
2 1 Rear Left Caster Wheel 2 Front Left Caster Wheel 9. Slide each caster wheel assembly up until it locks into place. 10. Lower server on to the pallet by removing the Side Bottom Foam Cushions. The server will have to be lifted slightly to pull out the cushions. Installing the Caster Wheels 11 - HP Integrity rx6600 | Rack to Pedestal Conversion Guide - HP Integrity rx6600 Se - Page 12
11. Place the ramp on the front of the pallet. See Figure 2-5 CAUTION: Do not roll the server off the pallet without first securing the ramp to the pallet. TIP: The ramp may also be attached to the rear of the pallet. Figure 2-5 - HP Integrity rx6600 | Rack to Pedestal Conversion Guide - HP Integrity rx6600 Se - Page 13
2-6 Ramp Attachment Detail CAUTION: Screws which are not fully inserted may hook the caster wheels or the bottom of the server. 13. Roll the server off the pallet. See Figure 2-5. Floor Installation Procedure Follow these steps to attach the caster wheels when the sever is on the floor. 1. Turn the - HP Integrity rx6600 | Rack to Pedestal Conversion Guide - HP Integrity rx6600 Se - Page 14
to turn on its side with the caster wheels attached. Figure 2-7 Caster Wheels on the Server Installing the Bezel Cover Follow these steps to install the bezel cover. 1. Attach the bezel cover to the front of the server starting from the server left. 2. Push the bezel cover into place against the - HP Integrity rx6600 | Rack to Pedestal Conversion Guide - HP Integrity rx6600 Se - Page 15
locking mechanism. This will make the hole appear partially blocked. 2. Hold the pedestal side flush against the server. 3. Slide the pedestal component forward until it locks into place Installing the Pedestal Kit Top Follow these steps to attach the pedestal top. 1. Align the holes in the pedestal - HP Integrity rx6600 | Rack to Pedestal Conversion Guide - HP Integrity rx6600 Se - Page 16
Rack System /E User's Manual at: http://www.hp.com under Enterprise Rack & Power Products, or other documentation that came with your rack kit for rack installation tool requirements. Powering Down the Server and Removing Cables Instructions for powering down the server, including removing cables - HP Integrity rx6600 | Rack to Pedestal Conversion Guide - HP Integrity rx6600 Se - Page 17
Figure 3-1 Server Rear 1 2 1 Finger Grips 2 Thumb Screws Removing the Pedestal Sides Follow these steps to remove the pedestal sides. 1. Looking has moved about 1/4 inch, the lock will release, and the screwdriver can be removed. 6. Pull the side away from the server. Removing the Pedestal Sides 17 - HP Integrity rx6600 | Rack to Pedestal Conversion Guide - HP Integrity rx6600 Se - Page 18
1 Locking Tab Removing the Caster Wheels 1. Turn the server onto its right side. WARNING! Be careful when lifting the server as it is heavy. CAUTION: Be sure the server handles are in (against the server) to prevent damaging the handles. The server will be slightly more difficult to turn on its side - HP Integrity rx6600 | Rack to Pedestal Conversion Guide - HP Integrity rx6600 Se - Page 19
the Caster Wheels 1 1 Metal Locking Tabs Installing the Server into the Rack For rack installation procedures refer to the server installation guide, users' guide, and the Rack System /E User's Manual at: http://www.hp.com under Enterprise Rack & Power Products, or other documentation that came with - HP Integrity rx6600 | Rack to Pedestal Conversion Guide - HP Integrity rx6600 Se - Page 20
feet removing, 18 pedestal sides installing, 15 removing, 17 pedestal top installing, 15 removing, 16 R rack component removal, 8 installation, 19 server removal, 8 S server powering down, 8, 16 static electricity (see electricity, static) T tools required pedestal assembly, 8 pedestal disassembly - HP Integrity rx6600 | Rack to Pedestal Conversion Guide - HP Integrity rx6600 Se - Page 21
*AB464-9009A* Printed in the US
HP Integrity rx6600 Rack to Pedestal
Conversion Guide
HP Part Number: AB464-9009A
Published: November 2006
Edition: 1