HP Kayak XA 05xx HP Kayak XA Series 05xx, Accessories Installation Guide For D - Page 16

Installing a Drive in a Front-Access Shelf

Page 16 highlights

HP Kayak XA 05xx PC Workstation - Installing Accessories In Your HP Desktop PC Workstation Installing Mass Storage Devices When an IDE Drive Is Installed NOTE 1 Switch on the computer. 2 To display the device in POST, press Esc while the PC Workstation re-starts. 3 If an error message appears, follow the instructions provided by the Error Message Utility. 4 To verify the configuration of your hard disk drive, press F2 to enter Setup when prompted. Once in Setup, select the Advanced menu, then the IDE Devices submenu. In the Primary Master item, check that the details for the device have been correctly detected by the Setup program. 5 Press F3 to save and exit Setup. Refer to the operating system documentation for information on formatting a drive. If an IDE drive is removed, switch on the computer. The system BIOS will detect that the device is missing. Press F4 to confirm that you want to remove the device. The system configuration will be updated automatically. Before Installing an IDE Device Before Installing a SCSI Device Installing a Drive in a Front-Access Shelf These instructions explain how to install a drive (such as a floppy disk drive, CD-ROM drive, CD-RW drive, or tape drive) in one of the frontaccess drive shelves. You should also refer to the manual supplied with the drive for any additional installation instructions. Refer to the drive's installation guide to see if you must set jumpers or if there is a special installation procedure to follow. If you are installing a SCSI device, refer to "Before Installing a SCSI Hard Disk" on page 11, before using the following instructions. 1 Disconnect the computer's power cord and any LAN or telecommunications cable. 2 Remove the computer's cover (refer to page 3). 16 English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22

HP Kayak XA 05xx PC Workstation
— Installing Accessories In Your HP Desktop PC Workstation
Installing Mass Storage Devices
16
English
When an IDE Drive
Is Installed
1
Switch on the computer.
2
To display the device in POST, press
Esc
while the PC Workstation
re-starts.
3
If an error message appears, follow the instructions provided by the
Error Message Utility.
4
To verify the configuration of your hard disk drive, press
F2
to enter
Setup
when prompted. Once in
Setup
, select the
Advanced
menu,
then the
IDE Devices
submenu. In the
Primary Master
item, check that the
details for the device have been correctly detected by the
Setup
program.
5
Press
F3
to save and exit
Setup
.
Refer to the operating system documentation for information on
formatting a drive.
NOTE
If an IDE drive is removed, switch on the computer. The system BIOS
will detect that the device is missing. Press
F4
to confirm that you want
to remove the device. The system configuration will be updated
automatically.
Installing a Drive in a Front-Access Shelf
These instructions explain how to install a drive (such as a floppy disk
drive, CD-ROM drive, CD-RW drive, or tape drive) in one of the front-
access drive shelves. You should also refer to the manual supplied with
the drive for any additional installation instructions.
Before Installing an
IDE Device
Refer to the drive’s installation guide to see if you must set jumpers or
if there is a special installation procedure to follow.
Before Installing a
SCSI Device
If you are installing a SCSI device, refer to “Before Installing a SCSI
Hard Disk” on page 11, before using the following instructions.
1
Disconnect the computer’s power cord and any LAN or
telecommunications cable.
2
Remove the computer’s cover (refer to page 3).