HP Kayak XU 04xx HP Kayak XU Series 04xx, Upgrade and Configuration Guide - Page 56

If You Can't Start the, Program, If the Date and Time Are Incorrect, If You Have a Network Problem

Get HP Kayak XU 04xx PDF manuals and user guides View all HP Kayak XU 04xx manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

2 Troubleshooting Your HP PC Workstation If Your PC Workstation Has a Software Problem 8 Press when prompted to use Setup. 9 Set new User and Administrator passwords. 10 Press to save the new passwords and exit Setup. If You Can't Start the Setup Program This may happen if the copy of the PC Workstation's configuration stored in CMOS is corrupted. You will need to erase this bad configuration. Refer to "Clearing the PC Workstation's Configuration Memory" on page 37 for more information on how to do this. If the Date and Time Are Incorrect The date and time can be incorrect for the following reasons: • The time has changed to reflect the beginning or end of Summer Time • The PC Workstation has been unplugged from the mains for too long and the battery is discharged. The on-board battery automatically recharges itself as soon as the PC Workstation is plugged into a power outlet. To change the date and time, use your operating system utilities or the Setup program. If You Have a Network Problem If you have a problem with your PC Workstation's network, run the HPIEDIAG utility provided on the HP CD-ROM that contains the LAN drivers, supplied with your PC Workstation. This utility should be run from a minimal DOS system, without any LAN drivers loaded-achieve this by booting from a system floppy disk. (If your PC Workstation is running Windows NT 4.0, you will need to create this system floppy disk on another PC.) 1 Insert the system floppy disk in the floppy disk drive and re-boot your PC Workstation. 48 English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
2
Troubleshooting Your HP PC Workstation
If Your PC Workstation Has a Software Problem
48
English
8
Press
when prompted to use
Setup
.
9
Set new User and Administrator passwords.
10
Press
to save the new passwords and exit
Setup
.
If You Can’t Start the
Setup
Program
This may happen if the copy of the PC Workstation’s configuration
stored in CMOS is corrupted. You will need to erase this bad
configuration. Refer to “Clearing the PC Workstation’s Configuration
Memory” on page 37 for more information on how to do this.
If the Date and Time Are Incorrect
The date and time can be incorrect for the following reasons:
•
The time has changed to reflect the beginning or end of
Summer Time
•
The PC Workstation has been unplugged from the mains for too long
and the battery is discharged.
The on-board battery automatically recharges itself as soon as the
PC Workstation is plugged into a power outlet.
To change the date and time, use your operating system utilities or the
Setup
program.
If You Have a Network Problem
If you have a problem with your PC Workstation’s network, run the
HPIEDIAG utility provided on the HP CD-ROM that contains the LAN
drivers, supplied with your PC Workstation. This utility should be run
from a minimal DOS system, without any LAN drivers loaded—achieve
this by booting from a system floppy disk. (If your PC Workstation is
running Windows NT 4.0, you will need to create this system floppy
disk on another PC.)
1
Insert the system floppy disk in the floppy disk drive and re-boot
your PC Workstation.