HP LH4r HP Netserver Service Handbook, Volume 3 - High-End - Page 66

Open = Off Closed = On, Front of NetServer

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 66 highlights

I/O Baseboard Battery Configuration Switch Block SCSI A SCSI B IDE (CD-ROM) Flexible Disk Drive I2C (J1F1) Remote Control Board Cable Auxiliary I2C 10 9 8 7 6 5 4 3 2 1 PCI LED Display Cable I/O Riser Slot P10-P9 +3.3 VDC 66/33 MHz Bus 3 P8-P7 +3.3 VDC 66/33 MHz Bus 2 64-bit P6-P3 +5 VDC 33 MHz Bus 1 Default P2-P1 +5 VDC 33 MHz Bus 0 Remote Control Board must be in slot P2. HP NetServer I/O Baseboard 1 Reserved 2 Recovery Boot Open 3 Reserved 4 Reserved 5 CMOS Clear 6 Paseword Clear Shaded rectangle 7 PCI Hot-Plug Switch Disable represents the 8 Reserved depressed side of the configuration Open = Off Closed = On switch Front of NetServer I/O Baseboard Jumper Settings 60

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
60
I/O Baseboard
Battery
IDE (CD-ROM)
Flexible Disk
Drive
SCSI A
SCSI B
I/O Riser
Slot
PCI LED
Display
Cable
IC
2
(J1F1)
Remote Control
Board Cable
Auxiliary I C
2
P10-P9
+3.3 VDC
66/33 MHz
P8-P7
+3.3 VDC
66/33 MHz
P6-P3
+5 VDC
33 MHz
P2-P1
+5 VDC
33 MHz
Remote Control
Board
must be
in slot P2.
10
9
8
7
6
5
4
3
2
1
Configuration
Switch Block
Bus 0
Bus 1
Bus 2
Bus 3
64-bit
Default
HP NetServer I/O Baseboard
Shaded rectangle
represents the
depressed side
of the configuration
switch
1
Reserved
Open
2
Recovery Boot
3
Reserved
4
Reserved
5
CMOS Clear
6
Paseword Clear
7
PCI Hot-Plug Switch Disable
8
Reserved
Open = Off Closed = On
Front of NetServer
I/O Baseboard Jumper Settings