HP LH4r HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 23

Step 3: Connect the Drive, Consult Information Assistant on

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

Chapter 2 Mount the Drive in the NetServer L Series Step 3: Connect the Drive In this step, you install the drive in the system, and connect the SCSI data cable and the drive power cable. The SCSI cable is connected to the SCSI connector on the system board or to a SCSI host bus adapter board. The correct cable for HP Ultra SCSI-3 drives has an active termination module on one end of the cable. The active termination module is easy to recognize, because it looks different from the other connectors on the cable, and the word "active" should appear on the active termination module. NOTE HP SCSI-3 drives must connect to the actively terminated cable. Using an incorrect cable (or not using an active termination module) will cause data transmission errors. Do not use passively terminated cables with Ultra SCSI-3 hard disk drives. CAUTION The active termination module belongs on the last connector on the cable, opposite the system board or host bus SCSI adapter. Do not remove this module. • Turn off your system and the display. • Disconnect the power cords. • Detach any external cables. • Remove the cover from the HP NetServer. • Remove any hardware necessary to reach the cables or insert the drive. Consult Information Assistant on the HP NetServer Navigator CD-ROM for your system for instructions. • Insert the mounted hard drive in your HP NetServer. • Connect the internal power supply cable to the hard disk drive with one of the unused cables from the power supply unit. • Select an available connector on the SCSI cable and connect it to the disk drive. 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
Chapter 2
Mount the Drive in the NetServer L Series
19
Step 3: Connect the Drive
In this step, you install the drive in the system, and connect the SCSI data cable
and the drive power cable. The SCSI cable is connected to the SCSI connector on
the system board or to a SCSI host bus adapter board.
The correct cable for HP Ultra SCSI-3 drives has an
active termination
module on
one end of the cable. The active termination module is easy to recognize, because
it looks different from the other connectors on the cable, and the word "active"
should appear on the active termination module.
NOTE
HP SCSI-3 drives must connect to the actively terminated
cable. Using an incorrect cable (or not using an active
termination module) will cause data transmission errors.
Do not
use passively terminated cables with Ultra SCSI-3 hard
disk drives.
CAUTION
The active termination module belongs on the last connector
on the cable, opposite the system board or host bus SCSI
adapter.
Do not remove this module
.
•
Turn off your system and the display.
•
Disconnect the power cords.
•
Detach any external cables.
•
Remove the cover from the HP NetServer.
•
Remove any hardware necessary to reach the cables or insert the drive.
Consult Information Assistant on the
HP NetServer Navigator
CD-ROM
for your system for instructions.
•
Insert the mounted hard drive in your HP NetServer.
•
Connect the internal power supply cable to the hard disk drive with one of
the unused cables from the power supply unit.
•
Select an available connector on the SCSI cable and connect it to the disk
drive.