HP LH4r HP Ultra/Wide SCSI 4 GB and 9 GB Hard Disk Drive - Page 27

Mount the Drive in the NetServer E€45, Step 1: Determine the Drive Location

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

3 Mount the Drive in the NetServer E 45 This chapter provides instructions for installing a hard disk drive in the HP NetServer E 45. Consider the following when installing a drive in an HP NetServer E Series system. • The HP NetServer E 45 supports up to four 4 GB or four 9 GB drives. • Drive types D4910A and D4911A are supported in the HP NetServer E 45. • Drive types D4910A and D4911A are not supported in the HP NetServer E 40 or the HP NetServer E 30. NOTE The HP NetServer E 45 ships with drive mounting trays installed in shelves 3 and 4. Drives shipped as accessories usually come installed on a factory tray, which must be removed. The drive must be put on an NetServer E 45 tray. Step 1: Determine the Drive Location The drive can be mounted in one of several possible locations in the system. If you decide to mount the drive on shelf 5 or 6 (recommended), you will fasten the drive to the chassis. If you decide to install the drive on shelf 3 or 4, you will mount the drive onto a tray, which is installed in one of the shelves. • Decide whether to mount the drive on shelf 5 or 6 (recommended) or on shelf 3 or 4. See Figure 3-1 for the locations of shelves in the system, and some of the cabling options. 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
23
3
Mount the Drive in the NetServer
E 45
This chapter provides instructions for installing a hard disk drive in the HP
NetServer E 45.
Consider the following when installing a drive in an HP NetServer E Series
system.
•
The HP NetServer E 45 supports up to four 4 GB or four
9 GB drives.
•
Drive types D4910A and D4911A are supported in the HP
NetServer E 45.
•
Drive types D4910A and D4911A are not supported in the HP NetServer E
40 or the HP NetServer E 30.
NOTE
The HP NetServer E 45 ships with drive mounting trays
installed in shelves 3 and 4. Drives shipped as accessories
usually come installed on a factory tray, which must be
removed. The drive must be put on an NetServer E 45 tray.
Step 1: Determine the Drive Location
The drive can be mounted in one of several possible locations in the system. If you
decide to mount the drive on shelf 5 or 6 (recommended), you will fasten the drive
to the chassis. If you decide to install the drive on shelf 3 or 4, you will mount the
drive onto a tray, which is installed in one of the shelves.
•
Decide whether to mount the drive on shelf 5 or 6 (recommended) or on
shelf 3 or 4. See Figure 3-1 for the locations of shelves in the system, and
some of the cabling options.