HP LH4r Installing Novell NetWare on an HP Netserver - Page 12

Tip #1. REGISTER MEMORY Command

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

http://support.novell.com Completing the Installation of the HP NetRAID-1Si/HP NetRAID-3Si I2O driver on NetWare 5.1/Small Business Suite 5/5.1 After the initial installation of NetWare, you may set the HP NetRAID-1Si or HP NetRAID-3Si adapter to operate in I2O mode. Perform the following: 1. Insert the NetWare 5.1 NOS drivers diskette into the floppy drive and copy the following files from the a:\i2odac directory to the C:\nwserver\drivers directory: BKSTROSM.* SCSIOSM.* 2. Next, edit the C:\NWSERVER\STARTUP.NCF file and add the following two lines after the LOAD I2OPCI.NLM statement. If the LOAD I2OPCI.NLM statement is not in the STARTUP.NCF file, add it. LOAD C:\NWSERVER\DRIVERS\BKSTROSM.HAM LOAD C:\NWSERVER\DRIVERS\SCSIOSM.HAM 3. Restart the server and use the NWCONFIG utility to create the necessary partitions and volumes. 4. Also load the NetRAID I2O compatibility driver, mril4_xx.ham, if: - An HP NetRAID (D4943A) or HP NetRAID-1 (D4992A) is present in the system (do not use the mega4_xx.ham driver in this case). - You wish to use the Hewlett-Packard NetRAID Config for NetWare or the HewlettPackard NetRAID Monitor for NetWare utility. 5. Use the NetRAID Express Tools (version B.02.02 or later) included with your adapter or on the NetServer Navigator CD to set the HP NetRAID-1Si or HP NetRAID-3Si into I2O mode. NOTE: Booting from the HP NetRAID-1Si or HP NetRAID-3Si using the I2O driver is not supported at this time. For more information consult the NetRAID adapter documentation. Section 5. General NetWare Installation Tips Tip #1. REGISTER MEMORY Command If the NetWare network operating system does not recognize installed system memory above 64 MB (for NetWare 4.xx) use the REGISTER MEMORY command to allow NetWare to use all available system memory.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
Completing the Installation of the HP NetRAID-1Si/HP NetRAID-3Si I2O driver on
NetWare 5.1/Small Business Suite 5/5.1
After the initial installation of NetWare, you may set the HP NetRAID-1Si or HP NetRAID-3Si
adapter to operate in I2O mode. Perform the following:
1. Insert the NetWare 5.1
NOS drivers diskette
into the floppy drive and copy the
following files from the
a:\i2odac
directory to the
C:\nwserver\drivers
directory:
BKSTROSM.*
SCSIOSM.*
2. Next, edit the
C:\NWSERVER\STARTUP.NCF
file and add the following two lines
after the
LOAD I2OPCI.NLM
statement. If the
LOAD I2OPCI.NLM
statement is not
in the
STARTUP.NCF
file, add it.
LOAD C:\NWSERVER\DRIVERS\BKSTROSM.HAM
LOAD C:\NWSERVER\DRIVERS\SCSIOSM.HAM
3.
Restart the server and use the
NWCONFIG
utility to create the necessary partitions and
volumes.
4.
Also load the NetRAID I2O compatibility driver,
mril4_xx.ham
, if:
- An HP NetRAID (D4943A) or HP NetRAID-1 (D4992A) is present in the system (do
not use the
mega4_xx.ham
driver in this case).
- You wish to use the
Hewlett-Packard NetRAID Config for NetWare
or the
Hewlett-
Packard NetRAID Monitor for NetWare
utility.
5. Use the
NetRAID Express Tools
(version B.02.02 or later) included with your adapter
or on the NetServer Navigator CD to set the HP NetRAID-1Si or HP NetRAID-3Si into
I2O mode.
NOTE: Booting from the HP NetRAID-1Si or HP NetRAID-3Si using the I2O driver is
not supported at this time. For more information consult the NetRAID adapter
documentation.
Section 5. General NetWare Installation Tips
Tip #1. REGISTER MEMORY Command
If the NetWare network operating system does not recognize installed system memory above 64
MB (for NetWare 4.xx) use the
REGISTER MEMORY
command to allow NetWare to use all
available system memory.