HP LH4r Installing Novell NetWare on an HP Netserver - Page 3

Installing the IDE CD-ROM Drive with FDATACD.SYS and MSCDEX.EXE, DEVICE=C, FDATACD.SYS /D

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 3 highlights

4. Select the desired driver. Once the desired driver is highlighted, insert a blank formatted 1.44 MB floppy diskette into the floppy drive and select Create Diskette(s). (Manual installation requires NOS Drivers diskette). 5. Repeat step 4 until all desired driver diskettes are created. 6. Select the Exit icon located in the bottom left hand corner of the screen after all driver diskettes have been created. Installing the IDE CD-ROM Drive with FDATACD.SYS and MSCDEX.EXE To install NetWare 4.2, you must first install a CD-ROM drive and driver in the DOS environment by using the driver diskettes you created using the HP NetServer Navigator CD. NOTE: DOS CD-ROM drivers are available on the NOS Drivers Diskette in the \Cdromdrv\IDEDOS directory. 1. Boot your HP NetServer using an MS DOS bootable utility diskette. 2. Use the fdisk utility to create a 250 MB primary DOS partition on the primary drive(C:). Remember to set the partition to active. 3. Use the format utility to format 250 MB partition. 4. Install DOS. (For detail instruction, see the instructions in the NetWare documentation.) NOTE: If applicable, make sure to remark the DOS=HIGH and the DEVICE=C:\DOS\HIMEM.SYS lines in the CONFIG.SYS file by inserting the command REM at the beginning of each line (i.e., REM DOS=HIGH). Otherwise NetWare may not function properly. 5. Insert the NOS Drivers Diskette created from the Navigator CD into the 1.44 MB floppy drive (A:). 6. Create a subdirectory on drive C by entering the command: MD directoryname where directoryname is a valid name for a directory (for example: doscdrom). 7. Copy all DOS CDROM drivers from drive A to this subdirectory, by entering the command: Copy A:\CDROMDRV\IDEDOS\*.* C:\directoryname 8. Use the edit utility to add the following lines to your CONFIG.SYS file: DEVICE=C:\directoryname\FDATACD.SYS /D:driver1 Where directoryname is the path to the directory containing the FDATACD.SYS driver, and driver1 specifies the driver signature name of the first CD-ROM device

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
4.
Select the desired driver. Once the desired driver is highlighted, insert a blank formatted
1.44 MB floppy diskette into the floppy drive and select
Create Diskette(s)
. (Manual
installation requires
NOS Drivers
diskette).
5.
Repeat step 4 until all desired driver diskettes are created.
6. Select the
Exit
icon located in the bottom left hand corner of the screen after all driver
diskettes have been created.
Installing the IDE CD-ROM Drive with FDATACD.SYS and MSCDEX.EXE
To install NetWare 4.2, you must first install a CD-ROM drive and driver in the DOS
environment by using the driver diskettes you created using the HP NetServer Navigator CD.
NOTE: DOS CD-ROM drivers are available on the NOS Drivers Diskette in the
\Cdromdrv\IDEDOS
directory.
1.
Boot your HP NetServer using an MS DOS bootable utility diskette.
2. Use the
fdisk
utility to create a 250 MB primary DOS partition on the primary drive(C:).
Remember to set the partition to active.
3. Use the
format
utility to format 250 MB partition.
4.
Install DOS. (For detail instruction, see the instructions in the NetWare documentation.)
NOTE: If applicable, make sure to remark the
DOS=HIGH
and the
DEVICE=C:\DOS\HIMEM.SYS
lines in the
CONFIG.SYS
file by
inserting the command
REM
at the beginning of each line (i.e.,
REM
DOS=HIGH
). Otherwise NetWare may not function properly.
5. Insert the
NOS Drivers Diskette
created from the Navigator CD into the 1.44 MB floppy
drive (A:).
6.
Create a subdirectory on drive
C
by entering the command:
MD
directoryname
where
directoryname
is a valid name for a directory (for example:
doscdrom
).
7.
Copy all DOS CDROM drivers from drive
A
to this subdirectory, by entering the
command:
Copy A:\CDROMDRV\IDEDOS\*.* C:\
directoryname
8. Use the
edit
utility to add the following lines to your
CONFIG.SYS
file:
DEVICE=C:\
directoryname
\FDATACD.SYS /D:
driver1
Where
directoryname
is the path to the directory containing the FDATACD.SYS
driver, and
driver1
specifies the driver signature name of the first CD-ROM device