HP Latex 1500 Site Preparation Guide
HP Latex 1500 Manual
 |
View all HP Latex 1500 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP Latex 1500 manual content summary:
- HP Latex 1500 | Site Preparation Guide - Page 1
HP Latex 1500 Printer Site Preparation Guide - HP Latex 1500 | Site Preparation Guide - Page 2
to change without notice. The only warranties for HP products and services are set forth in the express warranty statement accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors - HP Latex 1500 | Site Preparation Guide - Page 3
...1 System configuration ...1 Documentation ...1 Site preparation overview ...1 Customer responsibility ...2 2 Site preparation ...5 Planning for printer installation ...5 Installation time schedule ...5 System operation requirements ...6 Air supply requirements (pneumatic spindle) ...11 Room and - HP Latex 1500 | Site Preparation Guide - Page 4
iv ENWW - HP Latex 1500 | Site Preparation Guide - Page 5
The following manuals are provided with your printer, and can also be downloaded from http://www.hp.com/go/ Latex1500/manuals/: ● Introductory information ● Limited warranty ● Legal information ● Site preparation guide ● Site preparation checklist ● Installation guide ● User's guide Site preparation - HP Latex 1500 | Site Preparation Guide - Page 6
It is important to read the information provided in this guide thoroughly and ensure complete compliance with all installation and See Safety installations on page 14. RIP installation If you have bought HP RIP software for your printer: ● You must ensure that a computer is available on which to - HP Latex 1500 | Site Preparation Guide - Page 7
In order to perform remote support, the printer must have access to the printer) NOTE: In addition, you are recommended to have a second set of seven ink cartridges, four printheads, and one HP 871 Latex completed and returned to your reseller or service representative a minimum of two weeks before - HP Latex 1500 | Site Preparation Guide - Page 8
Dispose of liquid waste Dispose of liquid waste in compliance with all applicable federal, state, and local regulations. The waste profile datasheet contains the required information for an adequate disposal. This document is located here: https://hplatexknowledgecenter.com/applications/ - HP Latex 1500 | Site Preparation Guide - Page 9
method to ensure a smooth and trouble-free installation process is proper site provided in this guide. The installation process HP Scitex ONYX Thrive 211 RIP ● RIP-Queue ● Configure the printer (Quickset, Device output, Media, Page size, Properties) ● Main items of the Job Editor (Printer - HP Latex 1500 | Site Preparation Guide - Page 10
the information regarding the electrical configuration. The HP Internal Print Server can be powered with a single-phase line that can be used with an Uninterruptible Power Supply (UPS). The UPS must be rated to meet the power requirements of the printer, and should be in accordance with the wiring - HP Latex 1500 | Site Preparation Guide - Page 11
NOTE: Remember that you are required to follow the local laws, regulations, and standards that apply to the electrical installation of your printer. NOTE: The printer is not supplied with any power cable. Power distribution unit (PDU) The PDU must be rated to meet the power requirements of the - HP Latex 1500 | Site Preparation Guide - Page 12
Power specifications (continued) Input voltage (line to line) Input frequency Power consumption (typical) Maximum load current (per phase) 200-240V 50/60 Hz 8-10 kW 48 A Branch circuit-breaker specifications Three-phaseP 3 poles, 50/60 A AC Power-cable specifications Configuration Wire Terminals - HP Latex 1500 | Site Preparation Guide - Page 13
Power-cable specifications Configuration Wire Terminals External diameter range Three-phase line Single-phase line 5 wires, L1/L2/L3/N/PE 3 wires, L/N/PE Strained Cu minimum, 6 mm2 or 10 AWG Strained Cu minimum, 1.5 mm² or 16 AWG Lines, ferrule terminals, PE, M8 ring terminal Lines, ferrule - HP Latex 1500 | Site Preparation Guide - Page 14
branch circuit breaker in PDU (Power Distribution Unit) if so required by the Electrical Code of the local jurisdiction. WARNING! Ensure that the printer's built-in Residual-Current Circuit Breakers (RCCB) or Ground Fault Circuit Interrupters (GFCI) operate in the case of a current leakage fault to - HP Latex 1500 | Site Preparation Guide - Page 15
low voltage line shared with other users, the power line impedance Zmax must be less protection on the power supply to the printer. ● All electrical noise generating equipment, ground wire from the main building service panel. These should run in the by the customer. TIP: HP recommends that you use an - HP Latex 1500 | Site Preparation Guide - Page 16
correct operation of the printer. Failure to keep these environmental conditions within the standard ranges may cause image quality problems or damage sensitive Data Sheets. Consult the Safety Data Sheets available at http://www.hp.com/go/msds/ to identify the chemical ingredients of your ink - HP Latex 1500 | Site Preparation Guide - Page 17
minimum room volume of 100 m³. These specifications are valid for one HP printer printing a black area-fill print (high ink density) and fast lb) Your printer has four wheels used to move the printer and three feet that must be lowered to touch the ground and support the printer. The following - HP Latex 1500 | Site Preparation Guide - Page 18
level ● No holes or indentations ● Static-free surface (no carpet) ● Easy to clean ● Durable ● Free from strong vibrations ● Concrete Lighting Whenever your printer is in operation, the print production area should be well lit to provide the operator with optimal conditions for checking the color - HP Latex 1500 | Site Preparation Guide - Page 19
requires enough space to perform the following tasks: ● Print ● Use the HP Internal Print Server ● Replace a substrate roll ● Service the printer or replace printer components ● Ensure the printer is well ventilated Your printer has the following dimensions: Weight Width Depth Height 1200 kg (2645 - HP Latex 1500 | Site Preparation Guide - Page 20
area for materials When planning a storage area for materials used with the printer, thought should not only be given to safety and convenience, but that they can reach the required moistness and operating temperature. NOTE: HP substrate rolls have a 12 month warranty when the substrate rolls are - HP Latex 1500 | Site Preparation Guide - Page 21
NOTE: If needed, please instruct the customer IT to create routing rules that route around the to connect the printer to the network RIP requirements There are two RIPs offered by HP that may be used with the printer: ● HP Scitex ONYX Thrive 211 RIP: product number D9Z41A ● HP Scitex Caldera Grand - HP Latex 1500 | Site Preparation Guide - Page 22
connectivity: Gigabit Ethernet for TCP/IP printers NOTE: Firewall and antivirus must be disabled or configured to allow ONYX applications and printer ports (515, 1947, 8889, , see http://www.onyxgfx.com/system-specifications/. HP Scitex CALDERA GRAND RIP V10 (minimum configuration) ● Linux: - HP Latex 1500 | Site Preparation Guide - Page 23
For further details of Caldera configuration, see: ● http://www.caldera.eu/en/support.php?page=operating_system ● http://www.caldera.com/product/grandrip/ External color profiling In order to build color profiles for your printer, an external color sensor is needed. Make sure to choose an external - HP Latex 1500 | Site Preparation Guide - Page 24
to be designated that will be easily accessible to the delivery truck. This will require sufficient space to unload the large crate in which your printer is shipped. When planning this area, consider the following: ● Height and width of entrance to unloading area ● Ramps used to access the unloading - HP Latex 1500 | Site Preparation Guide - Page 25
guide. In exceptional cases, where ramps cannot be used due to a physical barrier, follow the alternative instructions indicated carefully. CAUTION: Unloading and moving the printer to lower the printer. Please follow the instructions carefully: ● The forklift can be ordered as a service kit (K4T88- - HP Latex 1500 | Site Preparation Guide - Page 26
● Two skates to move the crate (optional) ● Electric pallet jack (optional) 22 Chapter 3 Shipment arrival preparation ENWW - HP Latex 1500 | Site Preparation Guide - Page 27
● Manual pallet jack (optional) Above ground floor installation CAUTION: Unloading and moving the printer and all system components is the responsibility of the customer and not HP. Failure to provide the required moving and lifting equipment could result in personal injury or damage the printer - HP Latex 1500 | Site Preparation Guide - Page 28
packaging can be reused for moving the printer at a later date. The crate and packaging material that comes with the printer can also be disposed of. Most of the waste will be wood materials. Consult with your local authorities to determine the correct manner in which
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
 |
 |
HP Latex 1500 Printer
Site Preparation Guide