HP Latex 1500 Site Preparation Guide - Page 16

Pneumatic connector, Room and spacial requirements, Environmental specifications, Ventilation

Get HP Latex 1500 PDF manuals and user guides View all HP Latex 1500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Pneumatic connector The printer comes with an air gun that you must attach to your air supply. In order to connect your air supply to the air gun, you must meet the following requirements: ● 6.35 mm (0.25 in) female connector, BSP or NPT thread ● PTFE tape to secure the connection and prevent air leaks WARNING! Take care when using the air gun. When used for cleaning purposes, make sure to use it according to the local regulations since additional safety provisions may apply Room and spacial requirements Environmental specifications The temperature, humidity, and temperature gradient during operation and during storage must be kept within the standard ranges to ensure the correct operation of the printer. Failure to keep these environmental conditions within the standard ranges may cause image quality problems or damage sensitive electronic components. Temperature range Operating for optimal print quality 20 to 25°C (68 to 77°F) Operating for standard printing 15 to 30ºC Not operating (in transport or storage), ink in tubes 5 to 55°C (41 to 131°F) Not operating (in transport or storage), no ink in tubes -25 to 55°C (-13 to 131°F) Humidity range 30 to 60% Relative Humidity Temperature gradient 10°C/h (50°F/h) or less 20 to 70% 90% Relative Humidity at 55°C (131°F) 90% Relative Humidity at 55°C (131°F) 10°C/h (50°F/h) or less 10°C/h (50°F/h) or less 10°C/h (50°F/h) or less Maximum operating altitude: 3000 m (10000 ft) In addition to controlling the temperature, humidity, and temperature gradient, there are other environmental conditions that must be met during site preparation: ● Do not install the printer where it will be exposed to direct sunlight or a strong light source. ● Do not install the printer in a dusty environment. Remove any accumulated dust before moving the printer into the area. Ventilation Ensure that the room in which the system is installed meets local environmental, health, and safety (EHS) guidelines and regulations. Adequate ventilation needs to be provided to ensure that potential airborne exposure is adequately controlled, according to Safety Data Sheets. Consult the Safety Data Sheets available at http://www.hp.com/go/msds/ to identify the chemical ingredients of your ink consumables. Airborne materials can be identified and quantified by using established indoor air-quality testing protocols. HP performs these assessments during the development phase for all products. HP testing shows that, during printer operation, the concentrations of airborne contaminants measured in the workspace are consistently well below key occupational exposure limits. This observation is based on exposure assessments that model very active productivity at customer facilities. 12 Chapter 2 Site preparation ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
Pneumatic connector
The printer comes with an air gun that you must attach to your air supply. In order to connect your air supply to
the air gun, you must meet the following requirements:
●
6.35 mm (0.25 in) female connector, BSP or NPT thread
●
PTFE tape to secure the connection and prevent air leaks
WARNING!
Take care when using the air gun. When used for cleaning purposes, make sure to use it according to
the local regulations since additional safety provisions may apply
Room and spacial requirements
Environmental specifications
The temperature, humidity, and temperature gradient during operation and during storage must be kept within
the standard ranges to ensure the correct operation of the printer. Failure to keep these environmental
conditions within the standard ranges may cause image quality problems or damage sensitive electronic
components.
Temperature range
Humidity range
Temperature gradient
Operating for optimal print
quality
20 to 25°C (68 to 77°F)
30 to 60% Relative Humidity
10°C/h (50°F/h) or less
Operating for standard printing
15 to 30ºC
20 to 70%
10°C/h (50°F/h) or less
Not operating (in transport or
storage), ink in tubes
5 to 55°C (41 to 131°F)
90% Relative Humidity at 55°C
(131°F)
10°C/h (50°F/h) or less
Not operating (in transport or
storage), no ink in tubes
–25 to 55°C (–13 to 131°F)
90% Relative Humidity at 55°C
(131°F)
10°C/h (50°F/h) or less
Maximum operating altitude: 3000 m (10000 ft)
In addition to controlling the temperature, humidity, and temperature gradient, there are other environmental
conditions that must be met during site preparation:
●
Do not install the printer where it will be exposed to direct sunlight or a strong light source.
●
Do not install the printer in a dusty environment. Remove any accumulated dust before moving the printer
into the area.
Ventilation
Ensure that the room in which the system is installed meets local environmental, health, and safety (EHS)
guidelines and regulations.
Adequate ventilation needs to be provided to ensure that potential airborne exposure is adequately controlled,
according to Safety Data Sheets. Consult the Safety Data Sheets available at
go/msds/
to
identify the chemical ingredients of your ink consumables. Airborne materials can be identified and quantified by
using established indoor air-quality testing protocols.
HP performs these assessments during the development phase for all products. HP testing shows that, during
printer operation, the concentrations of airborne contaminants measured in the workspace are consistently well
below key occupational exposure limits. This observation is based on exposure assessments that model very
active productivity at customer facilities.
12
Chapter 2
Site preparation
ENWW