HP Latex 2700 User Guide 4

HP Latex 2700 Manual

Get HP Latex 2700 PDF manuals and user guides View all HP Latex 2700 manuals
Add to My Manuals
Save this manual to your list of manuals

HP Latex 2700 manual content summary:

  • HP Latex 2700 | User Guide 4 - Page 1
    HP Latex 126-in Roll-to-Freefall Kit User guide SUMMARY How to use your product.
  • HP Latex 2700 | User Guide 4 - Page 2
    accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. Safety notice Read and follow the operating and safety instructions before starting the printer.
  • HP Latex 2700 | User Guide 4 - Page 3
    -freefall roller and pinchwheels 8 Clean the roll-to-freefall roller ...8 Clean the pinchwheels ...9 4 Printcare diagnostics...11 Diagnostics for operator (HP Latex 1500 Printer) ...11 Diagnostics for operator (HP Latex 2700 printer series)...11 5 Roll-to-freefall system errors and alerts ...12 iii
  • HP Latex 2700 | User Guide 4 - Page 4
    while you are completing jobs. The roll-tofreefall configuration allows you to cut and remove prints as soon as they come off the printer, so that you can finish and deliver quickly. This accessory is compatible with the HP Latex 1500 Printer and the HP Latex 2700 printer series. Introduction 1
  • HP Latex 2700 | User Guide 4 - Page 5
    The substrate roll is mounted on the input spindle; the printed substrate will be deposited on the floor in front of the printer. NOTE: This video applies to HP Latex 800, HP Latex 1500, HP Latex 2700 series, and HP Latex 3000 series printers. The substrate goes from the input spindle over the main
  • HP Latex 2700 | User Guide 4 - Page 6
    You can load substrate with the printed face inwards or outwards on the spindle, in which case the spindle will turn in the opposite direction. The printer asks you for the winding direction if it cannot detect it automatically. Before loading a roll into the printer, you must have a roll loaded
  • HP Latex 2700 | User Guide 4 - Page 7
    taking care not to trap your fingers between the roller and the black substrate guide lying underneath and behind. 5. Close the latches at both sides. 6. Align the tension roller lever. 8. Go to the Internal Print Server and click or tap the Finish button as in the roll-to-roll configuration
  • HP Latex 2700 | User Guide 4 - Page 8
    bar. TIP: Do not try to load or unload the collector while printing. Before starting to load the substrate, select a tension bar of the , to be placed at each end to avoid lateral displacement of the tension bar during printing For example, you can make up the following tension bars. ● 914 mm (36
  • HP Latex 2700 | User Guide 4 - Page 9
    done in the center of the printer; so avoid putting your foot or any other object under the collector in the center. 7. Go to the Internal Print Server and click the Enable collector button (for the HP Latex 1500), or tap the Take-up reel button (for the HP Latex 2700 series). 6 Chapter 2 Substrate
  • HP Latex 2700 | User Guide 4 - Page 10
    . NOTE: The winding direction cannot be changed on the fly: the collector has to be deactivated and reactivated. 9. Click or tap the Finish button. The printer is now ready to print. Load a roll (roll-to-collector configuration) 7
  • HP Latex 2700 | User Guide 4 - Page 11
    's user guide. Prepare to clean the roll-to-freefall roller and pinchwheels The following steps provide the complete procedure for this topic. 1. Check that the printer is not printing. 2. Unload the substrate. 3. Raise the pressure roller lever if it was previously lowered. Clean the roll-to
  • HP Latex 2700 | User Guide 4 - Page 12
    a clean cloth dampened with water (for persistent dirt you may use isopropyl alcohol, but do not use petroleum-based cleaning liquids). 2. Turn the roller manually and keep cleaning to make sure the rubber surface of the roller is cleaned all around. WARNING! Take care not to trap your finger when
  • HP Latex 2700 | User Guide 4 - Page 13
    by pushing it (not by grabbing it). WARNING! Take special care when moving the roller backwards not to hit your fingers against the black substrate guide behind and under the roller. 6. Once the roller is in position, close the latches at both sides. 7. Ensure that the cleaned parts are completely
  • HP Latex 2700 | User Guide 4 - Page 14
    -collector sensor). This diagnostic makes automatic checks on the substrate floor motor and substrate output motor. Diagnostics for operator (HP Latex 2700 printer series) You can run these diagnostics only if the roll-to-freefall kit is installed. Roll-to-freefall kit Alert Recommendation
  • HP Latex 2700 | User Guide 4 - Page 15
    is no object blocking its line of sight. If the problem persists, run the sensors check diagnostic (41012) to check whether the sensor is working. If it is not, call your service representative. System errors and alerts for the HP Latex 2700 printer series Error 0010-0012-1215 E-cabinet MO/MF fuse
  • HP Latex 2700 | User Guide 4 - Page 16
    PCA Check that the TUR sensor cable is properly connected to the J49 connector on the e-box interconnect PCA. If the problem persists, call your service representative. 1041-0013-0009 RTFF switches not connected to e-box interconnect PCA Check that the roll-to-freefall switches sensor cable
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
HP Latex 126-in Roll-to-Freefall Kit
User guide
SUMMARY
How to use your product.