HP Latex 800 Site Preparation Guide - Page 12

Printing supplies, Return the site preparation checklist, Electrical configuration, Single-phase power

Get HP Latex 800 PDF manuals and user guides View all HP Latex 800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

If you are unable to determine whether you need a Web proxy or how to configure it, consult your network administrator or Internet Service Provider. If in doubt, you probably do not need a Web proxy. Printing supplies Some printing is done during the printer installation process, which requires some printing supplies (ink and substrate). The following supplies should be purchased in addition to the printer and should be available on the day of installation: ● Eight HP 832 Eco-Carton ink cartridges, one for each color (black, cyan, magenta, yellow, light cyan, light magenta, optimizer, and overcoat), for 700 series printers. ● Additionally, two HP 832 white Eco-Carton ink cartridges for 700 W printers. ● Eight 3 liter HP 873 Eco-Carton ink cartridges, one for each color (black, cyan, magenta, yellow, light cyan, light magenta, optimizer, and overcoat), for 800 series printers. ● Additionally, two 3 liter HP 873 white Eco-Carton ink cartridges for 800 W printers. ● At least one roll of substrate to perform calibrations and printhead alignment during printer setup. Return the site preparation checklist The checklist must be completed and returned to your reseller or service representative a minimum of two weeks before the day of installation. See Site preparation checklist on page 15. NOTE: Any delays during installation that are caused by an unprepared site will be charged to the customer. Take care that your site is properly prepared to ensure a smooth and easy installation. Electrical configuration Your printer requires the some electrical components to be supplied and installed by the customer, according to the Electrical Code requirements of the local jurisdiction of the country where the equipment is installed. NOTE: If configuration of the building electrical system used to power the printer needs to be modified to meet printer requirements, an electrician is required. Make sure that your electrician is appropriately certified according to local regulations and supplied with all the information regarding the electrical configuration. Components required: Single-phase power These are the printer's power-supply requirements. Table 2-5 Power specifications HP Latex 700 series HP Latex 800 series Number of power cords 2 Input voltage 200-240 V (two wires and protective earth) 8 Chapter 2 Site preparation requirements

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
If you are unable to determine whether you need a Web proxy or how to configure it, consult your network
administrator or Internet Service Provider. If in doubt, you probably do not need a Web proxy.
Printing supplies
Some printing is done during the printer installation process, which requires some printing supplies (ink and
substrate).
The following supplies should be purchased in addition to the printer and should be available on the day of
installation:
●
Eight HP 832 Eco-Carton ink cartridges, one for each color (black, cyan, magenta, yellow, light cyan, light
magenta, optimizer, and overcoat), for 700 series printers.
●
Additionally, two HP 832 white Eco-Carton ink cartridges for 700 W printers.
●
Eight 3 liter HP 873 Eco-Carton ink cartridges, one for each color (black, cyan, magenta, yellow, light cyan,
light magenta, optimizer, and overcoat), for 800 series printers.
●
Additionally, two 3 liter HP 873 white Eco-Carton ink cartridges for 800 W printers.
●
At least one roll of substrate to perform calibrations and printhead alignment during printer setup.
Return the site preparation checklist
The checklist must be completed and returned to your reseller or service representative a minimum of two weeks
before the day of installation.
See
Site preparation checklist
on page
15
.
NOTE:
Any delays during installation that are caused by an unprepared site will be charged to the customer.
Take care that your site is properly prepared to ensure a smooth and easy installation.
Electrical configuration
Your printer requires the some electrical components to be supplied and installed by the customer, according to
the Electrical Code requirements of the local jurisdiction of the country where the equipment is installed.
NOTE:
If configuration of the building electrical system used to power the printer needs to be modified to
meet printer requirements, an electrician is required. Make sure that your electrician is appropriately certified
according to local regulations and supplied with all the information regarding the electrical configuration.
Components required:
Single-phase power
These are the printer's power-supply requirements.
Table 2-5
Power specifications
HP Latex 700 series
HP Latex 800 series
Number of power cords
2
Input voltage
200–240 V (two wires and protective earth)
8
Chapter 2
Site preparation requirements