HP Pavilion 15-aw000 Maintenance and Service Guide - Page 61

Power button board see, System board see

Get HP Pavilion 15-aw000 PDF manuals and user guides View all HP Pavilion 15-aw000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

IMPORTANT: Make special note of each screw and screw lock size and location during removal and replacement Before removing the SD card reader board, follow these steps: 1. Shut down the computer. 2. Disconnect all external devices connected to the computer. 3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer. 4. Remove the base enclosure (see Base enclosure on page 28), and then remove the following components: a. Battery (see Battery on page 30). b. Optical drive (see Optical drive (select products only) on page 26). c. Hard drive (see Hard drive on page 31). d. Solid-state drive (see SSD (M.2) on page 33). e. Memory (see Memory on page 34). f. WLAN module (see WLAN module on page 37). g. Fan (see Fan on page 41). h. Heat sink (see Heat sink on page 43). i. I/O board (see I/O board on page 45). j. Power button board (see Power button board on page 46). k. System board (see System board on page 48). Remove the SD card reader board: ▲ Disconnect the zero-insertion force (ZIF) connector (1), remove 1 Phillips 2.0x2.5 screw (2), remove the board from the clip (3), lift the board (4), and then remove it (5). Component replacement procedures 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
IMPORTANT:
Make special note of each screw and screw lock size and location during removal
and replacement
Before removing the SD card reader board, follow these steps:
1.
Shut down the computer.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then
unplugging the AC adapter from the computer.
4.
Remove the base enclosure (see
Base enclosure
on page
28
), and then remove the following
components:
a.
Battery (see
Battery
on page
30
).
b.
Optical drive (see
Optical drive (select products only)
on page
26
).
c.
Hard drive (see
Hard drive
on page
31
).
d.
Solid-state drive (see
SSD (M.2)
on page
33
).
e.
Memory (see
Memory
on page
34
).
f.
WLAN module (see
WLAN module
on page
37
).
g.
Fan (see
Fan
on page
41
).
h.
Heat sink (see
Heat sink
on page
43
).
i.
I/O board (see
I/O board
on page
45
).
j.
Power button board (see
Power button board
on page
46
).
k.
System board (see
System board
on page
48
).
Remove the SD card reader board:
▲
Disconnect the zero-insertion force (ZIF) connector
(1)
, remove 1 Phillips 2.0x2.5 screw
(2)
, remove the
board from the clip
(3)
, lift the board
(4)
, and then remove it
(5)
.
Component replacement procedures
51