HP Pavilion TouchSmart 11-e040ca HP Pavilion TouchSmart 11 Notebook PC - Maint - Page 48

Power connector cable, Disconnect the power connector cable

Get HP Pavilion TouchSmart 11-e040ca PDF manuals and user guides View all HP Pavilion TouchSmart 11-e040ca manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

Reverse this procedure to install the display assembly. Power connector cable Description Power connector cable (includes bracket) Spare part number 730900-001 Before removing the power connector cable, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4. Remove the battery (see Battery on page 27). 5. Remove the service cover (see Service cover on page 28). Remove the power connector cable: 1. Remove the two Phillips PM2.0×5.5 screws (1) and the two Phillips PM2.5×10.5 screws (2) that secure the display assembly right hinge to the computer. 2. Open the display assembly right hinge (3) as far as it will open. 3. Disconnect the power connector cable (4) from the system board. 4. Release the power connector cable from the retention clips (2) and routing channel built into the bottom cover. 40 Chapter 6 Removal and replacement procedures for Authorized Service Provider parts

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
Reverse this procedure to install the display assembly.
Power connector cable
Description
Spare part number
Power connector cable (includes bracket)
730900-001
Before removing the power connector cable, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the battery (see
Battery
on page
27
).
5.
Remove the service cover (see
Service cover
on page
28
).
Remove the power connector cable:
1.
Remove the two Phillips PM2.0×5.5 screws
(1)
and the two Phillips PM2.5×10.5 screws
(2)
that
secure the display assembly right hinge to the computer.
2.
Open the display assembly right hinge
(3)
as far as it will open.
3.
Disconnect the power connector cable
(4)
from the system board.
4.
Release the power connector cable from the retention clips
(2)
and routing channel built into the
bottom cover.
40
Chapter 6
Removal and replacement procedures for Authorized Service Provider parts