HP Presario CQ60-100 HP G60 Notebook PC & Compaq Presario CQ60 Notebook PC - Page 48

from each side of the hard drive., If it is necessary to replace the hard drive bracket

Get HP Presario CQ60-100 - Notebook PC PDF manuals and user guides View all HP Presario CQ60-100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

Removal and replacement procedures 3. Remove the three Phillips PM2.5×4.0 screws 1 that secure the hard drive to the computer. 4. Grasp the Mylar tab 2 on the hard drive, and then slide the hard drive 3 to the right to disconnect it from the system board. 5. Remove the hard drive 4 from the hard drive bay. 6. If it is necessary to replace the hard drive bracket, remove the two Phillips PM3.0×4.0 hard drive bracket screws 1 from each side of the hard drive. 7. Lift the bracket 2 straight up to remove it from the hard drive. Reverse this procedure to reassemble and install the hard drive. 4-10 Maintenance and Service Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
4–10
Maintenance and Service Guide
Removal and replacement procedures
3. Remove the three Phillips PM2.5×4.0 screws
1
that secure the hard drive to the computer.
4. Grasp the Mylar tab
2
on the hard drive, and then slide the hard drive
3
to the right to disconnect it from the
system board.
5. Remove the hard drive
4
from the hard drive bay.
6. If it is necessary to replace the hard drive bracket, remove the two Phillips PM3.0×4.0 hard drive bracket
screws
1
from each side of the hard drive.
7. Lift the bracket
2
straight up to remove it from the hard drive.
Reverse this procedure to reassemble and install the hard drive.