HP Rp7410 Site Preparation Guide, Second Edition - hp rp7405/rp7410 Servers - Page 12

Safety and Regulatory, Safety in Material Handling - install guide

Page 12 highlights

Safety and Regulatory Regulatory Model: RSVLA-0102 For your protection, this product has been tested to various national and international regulations and standards. The scope of this regulatory testing includes electrical/mechanical safety, radio frequency interference, acoustics, and know hazardous materials.Where applicable, approvals obtained from third-party test agencies are shown on the product label. Safety in Material Handling WARNING Do not lift the cabinet manually. To avoid physical injury you must use a mechanical lifting device. WARNING Use care when working with hazardous voltages. This equipment may be configured with dual input line sources. Hazardous voltages and energy maybe present even after the removal of a single input source. Trained service personnel must follow the service guidelines. WARNING Do not stand in front of the equipment as it is rolled off the pallet onto the ramps. When removing the equipment from the shipping pallet, follow the guidelines specified in the Installation Procedures section of the appropriate equipment guides. NOTE Electrical practices and suggestions in this guide are based on North American practices. For countries outside North America, local electrical codes will take precedence over North American electrical codes. An example would be the recommendation that the PE (protective earthing) conductor be green with yellow stripes. This requirement is a North American directive and does not override the local code requirements for a country outside North America. Throughout this manual, the [LAHJ] acronym will be used to indicate Local Authority Has Jurisdiction. x

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74

x
Safety and Regulatory
Regulatory Model: RSVLA-0102
For your protection, this product has been tested to various national and international regulations and
standards. The scope of this regulatory testing includes electrical/mechanical safety, radio frequency
interference, acoustics, and know hazardous materials.Where applicable, approvals obtained from third-party
test agencies are shown on the product label.
Safety in Material Handling
WARNING
Do not lift the cabinet manually. To avoid physical injury you must use a mechanical
lifting device.
WARNING
Use care when working with hazardous voltages. This equipment may be configured
with dual input line sources. Hazardous voltages and energy maybe present even
after the removal of a single input source. Trained service personnel must follow the
service guidelines.
WARNING
Do not stand in front of the equipment as it is rolled off the pallet onto the ramps.
When removing the equipment from the shipping pallet, follow the guidelines
specified in the Installation Procedures section of the appropriate equipment
guides.
NOTE
Electrical practices and suggestions in this guide are based on North American practices. For
countries outside North America, local electrical codes will take precedence over North
American electrical codes.
An example would be the recommendation that the PE (protective earthing) conductor be green
with yellow stripes. This requirement is a North American directive and does not override the
local code requirements for a country outside North America.
Throughout this manual, the [LAHJ] acronym will be used to indicate Local Authority Has Jurisdiction.