HP Scitex FB950 HP Scitex FB950 - User Guide - Page 32

Restore loaded state, Proceed, Go Online, Advance Media, Turn Off Fans

Get HP Scitex FB950 PDF manuals and user guides View all HP Scitex FB950 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

The printer measures the media width. 21. On the Front Page screen, press the Proceed (►) key. The Front Page screen appears on the control panel. 22. Press the Go Online key. The printer is now ready to receive a print job from the RIP. Restore loaded state 1. As prompted by the control panel, remove the foam press roller, then press the Proceed (►) key. 2. Press the upper (forward) Advance Media key to advance the media to the takeup spool and/or past any printed area of the media. 3. On the control panel, press the Turn Off Fans key. 4. Hold the upper (forward) Advance Media key down for about five seconds. 5. On the control panel, press the Turn On Fans key. 6. Press the Proceed (►) key. 7. Check for wrinkles in the media across the full length and width of the belt. If you see any wrinkles, turn off the fans and smooth them out with your hand. Repeat steps 3 through 7 until no wrinkles are visible. 8. Place the foam press roller (3) into operating position. 9. If you are not using the takeup system, or if the media is already loaded in the takeup, go to step 15. 10. Align the cardboard takeup core to the media and tighten the collets to lock the core in place. 11. Lift the first dancer bar (6) (with the gears), and lock in the upper position. 12. Pull the media under the first dancer bar, over second dancer bar (7), and down to the printer side of takeup roller (8). Looking down the length of the takeup roller from the user end, the roller rotates clockwise. Ensure that the media is wrapped as shown in Figure 2-1 Roll-fed media path on page 24. 13. Tape the end of the media to printer side of takeup roller, starting in the middle and working out to both ends. Be sure to maintain even tension across the width of the media. 14. Release the dancer bar locking lever. 15. Press the Proceed key (►). 16. Enter the media length or press the Esc key for an undefined length. The printer measures the media width. 17. Press the Proceed key (►). The Front Page screen appears on the control panel. 18. On the Front Page screen, press the Go Online key. The printer is now ready to receive a print job from the RIP. 26 Chapter 2 Printing ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
The printer measures the media width.
21.
On the Front Page screen, press the
Proceed
(
►
) key.
The Front Page screen appears on the control panel.
22.
Press the
Go Online
key.
The printer is now ready to receive a print job from the RIP.
Restore loaded state
1.
As prompted by the control panel, remove the foam press roller, then press the
Proceed
(
►
) key.
2.
Press the upper (forward)
Advance Media
key to advance the media to the takeup spool and/or
past any printed area of the media.
3.
On the control panel, press the
Turn Off Fans
key.
4.
Hold the upper (forward)
Advance Media
key down for about five seconds.
5.
On the control panel, press the
Turn On Fans
key.
6.
Press the
Proceed
(
►
) key.
7.
Check for wrinkles in the media across the full length and width of the belt.
If you see any wrinkles, turn off the fans and smooth them out with your hand. Repeat steps 3
through 7 until no wrinkles are visible.
8.
Place the foam press roller (3) into operating position.
9.
If you are not using the takeup system, or if the media is already loaded in the takeup, go to step
15.
10.
Align the cardboard takeup core to the media and tighten the collets to lock the core in place.
11.
Lift the first dancer bar (6) (with the gears), and lock in the upper position.
12.
Pull the media under the first dancer bar, over second dancer bar (7), and down to the printer side
of takeup roller (8).
Looking down the length of the takeup roller from the user end, the roller rotates clockwise. Ensure
that the media is wrapped as shown in
Figure
2
-
1
Roll-fed media path
on page
24
.
13.
Tape the end of the media to printer side of takeup roller, starting in the middle and working out to
both ends.
Be sure to maintain even tension across the width of the media.
14.
Release the dancer bar locking lever.
15.
Press the
Proceed
key (
►
).
16.
Enter the media length or press the
Esc
key for an undefined length.
The printer measures the media width.
17.
Press the
Proceed
key (
►
).
The Front Page screen appears on the control panel.
18.
On the Front Page screen, press the
Go Online
key.
The printer is now ready to receive a print job from the RIP.
26
Chapter 2
Printing
ENWW