HP StorageWorks Modular Smart Array 1000 HP StorageWorks 1000/1500 Modular Sma - Page 24

Flash All Attached Fan Control Modules, Continue, Flash Successful

Get HP StorageWorks Modular Smart Array 1000 PDF manuals and user guides View all HP StorageWorks Modular Smart Array 1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

• Flash All Attached Fan Control Modules: Update the fan module firmware on the MSA fans, including fans in any MSA20 storage enclosures attached to the selected MSA. NOTE: If an updating option is not supported for the bundled firmware or hardware configuration, the option is shaded and cannot be selected. 7. Read the warning window, and then click Continue. The updating process automatically begins, updating the specified components. NOTE: The MSA controller displays the message FIRMWARE FLASH STARTED when it starts the download, and FIRMWARE FLASH DONE when the download is complete. 8. Wait for the Flash Successful pop-up message to be displayed. 9. Click Exit. 10. Power-cycle the updated MSA and any attached storage enclosures in the following sequence: NOTE: The MSA storage system must be restarted to activate new firmware. a. Press and hold down the MSA Power on/Standby button for approximately five seconds to place the MSA in Standby mode. b. Power off all storage enclosures attached to the MSA. c. Wait approximately two minutes to ensure that the hard disk drives in the enclosures stop rotating. d. Restart all storage enclosures attached to the MSA. e. Wait approximately four minutes to allow the enclosures to complete their startup routines. f. Press and release the MSA Power on/Standby button to restart the MSA. g. Wait (up to eight minutes) for the STARTUP COMPLETE message to display on the MSA controller LCD panel. 24 Updating the components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
•
Flash All Attached Fan Control Modules
: Update the fan module
fi
rmware on the MSA fans,
including fans in any MSA20 storage enclosures attached to the selected MSA.
NOTE:
If an updating option is not supported for the bundled
fi
rmware or hardware con
fi
guration,
the option is shaded and cannot be selected.
7.
Read the warning window, and then click
Continue
.
The updating process automatically begins, updating the speci
fi
ed components.
NOTE:
The MSA controller displays the message
FIRMWARE FLASH STARTED
when it starts the
download, and
FIRMWARE FLASH DONE
when the download is complete.
8.
Wait for the
Flash Successful
pop-up message to be displayed.
9.
Click
Exit
.
10.
Power-cycle the updated MSA and any attached storage enclosures in the following sequence:
NOTE:
The MSA storage system must be restarted to activate new
fi
rmware.
a.
Press and hold down the MSA Power on/Standby button for approximately
fi
ve seconds to
place the MSA in Standby mode.
b.
Power off all storage enclosures attached to the MSA.
c.
Wait approximately two minutes to ensure that the hard disk drives in the enclosures stop
rotating.
d.
Restart all storage enclosures attached to the MSA.
e.
Wait approximately four minutes to allow the enclosures to complete their startup routines.
f.
Press and release the MSA Power on/Standby button to restart the MSA.
g.
Wait (up to eight minutes) for the
STARTUP COMPLETE
message to display on the MSA
controller LCD panel.
24
Updating the components