HP StorageWorks Modular Smart Array 1000 HP StorageWorks 1000/1500 Modular Sma - Page 33

Firmware Flash Started, Msa Controller

Get HP StorageWorks Modular Smart Array 1000 PDF manuals and user guides View all HP StorageWorks Modular Smart Array 1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

Delaying for 120 seconds while firmware is saved, please be patient... 120 The utility counts down from 120 seconds, returning to the scu prompt when the time delay is complete. CAUTION: Do not restart the server. NOTE: The MSA controller displays the message FIRMWARE FLASH STARTED when it starts the download, and FIRMWARE FLASH DONE when the download is complete. 6. After the MSA controller displays FIRMWARE FLASH DONE, do one of the following: • If you have one MSA with a single-controller, the firmware update is complete. Proceed to Step 7. • If you have one MSA with dual controllers, you must update the firmware on the second controller. Repeat Step 5 for the second controller. • If you have multiple MSA, repeat Step 5for each controller in each MSA. 7. After the firmware has been updated on all MSA controllers, exit the SCU by entering: scu> exit 8. After the firmware has been updated on all MSA controllers, restart your system using the following sequence: a. Shut down the operating system on each server. b. Remove power from each MSA. c. After a few moments, reapply power to the MSA. When the MSA completes its startup routine, the STARTUP COMPLETE message is displayed. d. After the MSA has completed its startup routine, restart each AlphaServer. 9. Verify that the controller firmware was updated by entering: scu> show edt | grep MSA | grep -v VOLUME 0 0 0 RAID !ANSI MSA CONTROLLER 6.86 n 6 0 0 RAID !ANSI MSA CONTROLLER 6.86 n 7 0 0 RAID !ANSI MSA CONTROLLER 6.86 n 8 0 0 RAID !ANSI MSA CONTROLLER 6.86 n 10. Before resuming I/O access to the MSA, from the server, verify that the MSA and its storage arrays are online. 1000/1500 Modular Smart Array firmware updating guide 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
Delaying for 120 seconds while firmware is saved, please be
patient... 120
The utility counts down from 120 seconds, returning to the scu prompt when the time delay is
complete.
CAUTION:
Do not restart the server.
NOTE:
The MSA controller displays the message
FIRMWARE FLASH STARTED
when it
starts the download, and
FIRMWARE FLASH DONE
when the download is complete.
6.
After the MSA controller displays
FIRMWARE FLASH DONE
, do one of the following:
•
If you have one MSA with a single-controller, the
fi
rmware update is complete. Proceed
to
Step 7
.
•
If you have one MSA with dual controllers, you must update the
fi
rmware on the second
controller. Repeat
Step 5
for the second controller.
•
If you have multiple MSA, repeat
Step 5
for each controller in each MSA.
7.
After the
fi
rmware has been updated on all MSA controllers, exit the SCU by entering:
scu> exit
8.
After the
fi
rmware has been updated on all MSA controllers, restart your system using the following
sequence:
a.
Shut down the operating system on each server.
b.
Remove power from each MSA.
c.
After a few moments, reapply power to the MSA.
When the MSA completes its startup routine, the
STARTUP COMPLETE
message is displayed.
d.
After the MSA has completed its startup routine, restart each AlphaServer.
9.
Verify that the controller
fi
rmware was updated by entering:
scu> show edt | grep MSA | grep -v VOLUME
0
0
0
RAID
!ANSI
MSA CONTROLLER
6.86
n
6
0
0
RAID
!ANSI
MSA CONTROLLER
6.86
n
7
0
0
RAID
!ANSI
MSA CONTROLLER
6.86
n
8
0
0
RAID
!ANSI
MSA CONTROLLER
6.86
n
10.
Before resuming I/O access to the MSA, from the server, verify that the MSA and its storage arrays
are online.
1000/1500 Modular Smart Array
fi
rmware updating guide
33