HP StorageWorks Modular Smart Array 1000 HP StorageWorks 1000/1500 Modular Sma - Page 30

Msa> Flash Firmware Msav686b272.bin, Msa> Set Controller $1$gga400.

Get HP StorageWorks Modular Smart Array 1000 PDF manuals and user guides View all HP StorageWorks Modular Smart Array 1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

7. Enter the following command to open the MSA_UTIL firmware flash program: RUN SYS$ETC:MSA_UTIL 8. Enter the show controller command to see a list of MSA controllers on the SAN: Example command and response: MSA> SHOW CONTROLLER/BRIEF A default controller is not set. All matching controllers displayed: Controller: $1$GGA400: MSA1xxx (C) COMPAQ P56350B9IMX025 Software 3.36 NODE_ID = 500805f3-0001b290 Controller Identifier: 400 Current Redundancy mode: Active/Standby Current Role: Active Controller: $1$GGA401: Controller Identifier: 401 MSA1xxx (C) COMPAQ P56350B9IN20HW NODE_ID = 500805f3-0001b290 Current Redundancy mode: Active/Standby Current Role: Standby Software 3.36 9. Enter the set controller command to indicate the controller to be flashed: Example command and response, using the sample information in Step 8: MSA> SET CONTROLLER $1$GGA400. 10. Enter the flash firmware command to begin the update: Example command and response, using the sample information in Step 1: MSA> FLASH FIRMWARE MSAV686B272.BIN Sending Flash Command. Please wait. New firmware will be loaded when THIS_CONTROLLER is reset. NOTE: The MSA displays the message FIRMWARE FLASH STARTED when it starts the download and FIRMWARE FLASH DONE when the download is complete. 11. After the controller displays FIRMWARE FLASH DONE, do one of the following: • If you have one MSA with a single controller, the firmware update procedure is complete. Proceed to Step 12. • If you have one MSA with dual controllers, you must update the firmware on the second controller. Repeat Step 8 through Step 10to update the firmware on that controller. • If you have multiple MSAs, repeat Step 8 through Step 10 for each controller in each MSA. 12. Enter the following command to exit the update utility: MSA> EXIT 13. After all MSA controllers have been updated and the controller displays FIRMWARE FLASH DONE, power-cycle the MSA by doing the following: a. Remove power from the MSA. b. After a few moments, reapply power to the MSA. After the MSA completes its start up routine, the STARTUP COMPLETE message is displayed: 14. To verify that the firmware was updated, use the following commands: $ RUN SYS$$ETC:MSA_UTIL MSA> SHOW CONTROLLER/BRIEF A default controller is not set. All matching controllers displayed: 30 Updating the components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
7.
Enter the following command to open the MSA_UTIL
fi
rmware
fl
ash program:
RUN SYS$ETC:MSA_UTIL
8.
Enter the
show controller
command to see a list of MSA controllers on the SAN:
Example command and response:
MSA> SHOW CONTROLLER/BRIEF
A default controller is not set. All matching controllers displayed:
Controller:
$1$GGA400:
MSA1xxx
(C)
COMPAQ
P56350B9IMX025
Software 3.36
NODE_ID = 500805f3-0001b290
Controller Identifier:
400
Current Redundancy mode: Active/Standby
Current Role: Active
Controller:
$1$GGA401:
Controller Identifier:
401
MSA1xxx
(C)
COMPAQ
P56350B9IN20HW
Software 3.36
NODE_ID = 500805f3-0001b290
Current Redundancy mode: Active/Standby
Current Role: Standby
9.
Enter the
set controller
command to indicate the controller to be
fl
ashed:
Example command and response,
using the sample information in
Step 8
:
MSA> SET CONTROLLER $1$GGA400.
10.
Enter the
flash firmware
command to begin the update:
Example command and response,
using the sample information in
Step 1
:
MSA> FLASH FIRMWARE MSAV686B272.BIN
Sending Flash Command.
Please wait.
New firmware will be loaded when THIS_CONTROLLER is reset.
NOTE:
The MSA displays the message
FIRMWARE FLASH STARTED
when it starts the download
and
FIRMWARE FLASH DONE
when the download is complete.
11.
After the controller displays
FIRMWARE FLASH DONE
, do one of the following:
•
If you have one MSA with a single controller, the
fi
rmware update procedure is complete.
Proceed to
Step 12
.
•
If you have one MSA with dual controllers, you must update the
fi
rmware on the second
controller. Repeat
Step 8
through
Step 10
to update the
fi
rmware on that controller.
•
If you have multiple MSAs, repeat
Step 8
through
Step 10
for each controller in each MSA.
12.
Enter the following command to exit the update utility:
MSA> EXIT
13.
After all MSA controllers have been updated and the controller displays
FIRMWARE FLASH DONE
,
power-cycle the MSA by doing the following:
a.
Remove power from the MSA.
b.
After a few moments, reapply power to the MSA.
After the MSA completes its start up routine, the
STARTUP COMPLETE
message is displayed:
14.
To verify that the
fi
rmware was updated, use the following commands:
$ RUN SYS$$ETC:MSA_UTIL
MSA> SHOW CONTROLLER/BRIEF
A default controller is not set. All matching controllers displayed:
30
Updating the components