Home » HP Manuals » Storage Devices » HP Surestore Disk Array FC60 » Manual Viewer

HP Surestore Disk Array FC60 HP SureStore E Disk Array 12H User's and Service - Page 20

Connecting Power Cords, Installing Modules

Get HP Surestore Disk Array FC60 PDF manuals and user guides

View all HP Surestore Disk Array FC60 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Description Product Description Connecting Power Cords Connecting Power Cords You should connect power cords to all ac power connectors (see Figure 3). Disk array availability is enhanced if each power cord is connected to a separate ac branch circuit. WARNING! To avoid a fire hazard, the ac branch service must be properly currentprotected by either a fuse or a circuit breaker. Use only UL/CSA approved power cord, SVT type, rated for suitable voltage and current. These power cords have two conductors and a ground. Failure to use the proper power cord may result in a shock or fire hazard. Installing Modules This chapter shows how to install modules into the disk array. NOTE! To improve enclosure cooling and balance the load on the internal SCSI buses, the disk modules should be installed from left to right and from top to bottom. Disk module SCSI addresses are automatically preset by the backplane inside the disk array enclosure upon insertion. 20

Section	Page
Table of Contents	3
Product Description	9
Models and Configurations Available	9
Options	10
Available Accessories	13
Unpacking and Repackaging the Disk Array	14
Product Features	16
Connecting Power Cords	20
Installing Modules	20
Controller Module	22
SCSI Cabling Requirements	25
Connecting SCSI Cabling	25
Fibre Channel (FC) SCSI Multiplexer (MUX) Connection	32
Switching Power On	32
Switching Power Off	32
HP SureStore E Disk Array 12H Controller	33
About Battery Packs	33
Installing Controller Batteries	34
Replacing Controller Batteries	36
Downloading Array Controller Firmware	37
Firmware Download Procedure	39
Operating the Control Panel	69
Using the Control Panel	69
Control Panel Status Light Operation	70
Using the Control Panel Buttons	71
Using Control Panel Menus	75
Concepts and Management	83
Disk Arrays in Brief	83
Disk Array Features	84
Disk Array Hardware	93
Managing the Disk Array Capacity	100
Upgrading the Capacity of a Fully-Loaded Disk Array	104
Optimizing Performance	105
Troubleshooting	113
Module Slot Numbers	113
Module Status Lights	113
Replacing Modules	115
Troubleshooting Procedures	119
Power On Sequence Test	121
Control Panel Error Messages	123
FRU Codes	133
Event Code Descriptions	134
Preventive Maintenance	189
Tools Required	189
Required Preventive Maintenance	189
Removal and Replacement	191
Tools Required	191
Replacing a Failed Controller ModuleŒHP-qualified personnel only	191
Front Door AssemblyŒHP-qualified personnel only	192
Display ModuleŒHP-qualified personnel only	194
Backplane AssemblyŒHP-qualified personnel only	196
Power Button and Push RodŒHP-qualified personnel only	200
AC Power ReceptacleŒHP-qualified personnel only	201
Module Cam LeverŒHP-qualified personnel only	203
Replaceable Part Numbers	205
Appendix A. Product Specifications	211
Enclosure Physical Specifications	211
Operating Characteristics and Requirements	212
Environmental Requirements	213
Enclosure Features	215
Module Specifications	216
Appendix B. Regulatory/Safety Statements	217
FCC Statement (For U.S.A. Only)	217
Spécification ATI Classe A (France Seulement)	219
Product Noise Declaration (For Germany Only)	220
Geräuschemission (For Germany Only)	220
Electromagnetic Compatibility	221
Safety Specifications	221
Declaration of Conformity	222
Appendix C. Cabinet Configurations	223
Cabinet Configurations Available	223
Deskside Cabinet	223
Unpacking the Deskside Cabinet	224
Installing the Disk Array into the Deskside Cabinet	226
Deskside Cabinet Cabling	228
Rackmount Cabinets	229
Appendix D. Back-to-Back Racking	235
Product Description	235
Installation	239
Installation Procedure	242
Troubleshooting	252
Problem Resolution	255
Removal and Replacement	257
Specifications	258
Frequently-asked Questions	259

Match case Limit results 1 per page

Product Description

Connecting Power Cords

Description

Connecting Power Cords

You should connect power cords to all ac power connectors (see

Figure 3

). Disk array availability is

enhanced if each power cord is connected to a separate ac branch circuit.

WARNING!

To avoid a fire hazard, the ac branch service must be properly current-

protected by either a fuse or a circuit breaker. Use only UL/CSA approved power cord, SVT

type, rated for suitable voltage and current. These power cords have two conductors and a

ground. Failure to use the proper power cord may result in a shock or fire hazard.

Installing Modules

This chapter shows how to install modules into the disk array.

NOTE!

To improve enclosure cooling and balance the load on the internal SCSI buses, the disk

modules should be installed from left to right and from top to bottom. Disk module SCSI

addresses are automatically preset by the backplane inside the disk array enclosure upon

insertion.