HP XM600 hp kayak xm600, installing and replacing hardware parts in your pc wo
HP XM600 - Kayak - 128 MB RAM Manual
 |
View all HP XM600 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP XM600 manual content summary:
- HP XM600 | hp kayak xm600, installing and replacing hardware parts in your pc wo - Page 1
and replacing hardware parts in your PC Workstation. Processor Fan Power Supply Unit HP UltraFlow Airflow Guide Secondary Hard Disk Drive tray Primary Hard Disk Drive Bay HP Master Key Lock Depending on the model, the memory module sockets support either: • Two RDRAM modules. • Two SDRAM - HP XM600 | hp kayak xm600, installing and replacing hardware parts in your pc wo - Page 2
your own safety, it is recommended that you first read the warning notices in the Introductory Section. 1 Switch off the display and PC Workstation. Disconnect all power cables and any LAN or telecommunications cables. 2 If necessary, unlock the cover using the key on the front panel. 3 Unscrew - HP XM600 | hp kayak xm600, installing and replacing hardware parts in your pc wo - Page 3
Bezel Installing and Replacing Hardware Parts in Your PC Workstation Removing and Replacing the Cover If necessary, replace the front bezel. To do this, align the three guide pins located at the bottom of the bezel with their associated slots on the all the power and telecommunications cables. 3 - HP XM600 | hp kayak xm600, installing and replacing hardware parts in your pc wo - Page 4
Removing and Replacing the Airflow Guide 1 Switch off the display and PC Workstation. Disconnect all power cables and any LAN or telecommunications cables. 2 Remove the PC Workstation's cover (refer to page 2 for instructions). 3 Slide the HP UltraFlow Airflow Guide towards the front access shelf - HP XM600 | hp kayak xm600, installing and replacing hardware parts in your pc wo - Page 5
Single-processor systems can be upgraded to dual-processor systems by installing a second processor in the vacant processor slot. The second processor must be of the same type, speed and level-2 cache memory capacity as the first. 1 Switch off the display and PC Workstation. Disconnect all power - HP XM600 | hp kayak xm600, installing and replacing hardware parts in your pc wo - Page 6
3 Replace the HP UltraFlow Airflow Guide (refer to page 4). 4 Replace the PC Workstation's cover (refer to page 3). Reconnect all the power and telecommunications cables. The processor type and speed is automatically recognized by the BIOS. HP DualExpress! Included with the HP Processor Accessory is - HP XM600 | hp kayak xm600, installing and replacing hardware parts in your pc wo - Page 7
Workstation Removing, Replacing and Upgrading Memory on Models Shipped with SDRAM Removing, Replacing and Upgrading Memory on Models Shipped with SDRAM Upgrading SDRAM Memory SDRAM models of the HP Kayak XM600 are supplied with a Memory Expansion Card supporting one or two Synchronized Dynamic RAM - HP XM600 | hp kayak xm600, installing and replacing hardware parts in your pc wo - Page 8
on the system board, RIMM0 and RIMM1 must contain a continuity module. Removing the Memory Expansion Card 1 Switch off the display and PC Workstation. Disconnect all power cables and any LAN or telecommunications cables. 2 Remove the PC Workstation's cover (refer to page 2 for instructions - HP XM600 | hp kayak xm600, installing and replacing hardware parts in your pc wo - Page 9
Parts in Your PC Workstation Removing, Replacing and Upgrading Memory on Models Shipped with SDRAM Replacing the Memory Expansion Card 1 Install the Memory Expansion Card so that the memory modules face the processor. 2 With the two retaining clips on the system board open, press the Memory - HP XM600 | hp kayak xm600, installing and replacing hardware parts in your pc wo - Page 10
Parts in Your PC Workstation Removing, Replacing and Upgrading Memory on Models Shipped with RDRAM Removing, Replacing and Upgrading Memory on Models Shipped with RDRAM Upgrading RDRAM Memory RDRAM models of the HP Kayak XM600 PC Workstation support one or two RAMBUS Direct RAM (RDRAM) memory - HP XM600 | hp kayak xm600, installing and replacing hardware parts in your pc wo - Page 11
and Replacing Hardware Parts in Your PC Workstation Removing, Replacing and Upgrading Memory on Models Shipped with RDRAM 8 Check the HP Summary Screen to verify the new configuration (refer to "Viewing the HP Summary Screen" in the Section on "Setting Up and Using Your PC Workstation") 11 - HP XM600 | hp kayak xm600, installing and replacing hardware parts in your pc wo - Page 12
Your PC Workstation Removing and Replacing a PCI Accessory Card Removing and Replacing a PCI Accessory Card The HP Kayak XM600 has five 32-bit 33 MHz PCI accessory card slots and one AGP slot on the system board. The AGP slot accepts standard 25 W AGP video cards. NOTE Higher power AGP PRO video - HP XM600 | hp kayak xm600, installing and replacing hardware parts in your pc wo - Page 13
Parts in Your PC Workstation Installing Mass Storage Devices Installing Mass Storage Devices The PC has an integrated Ultra ATA-66 controller that supports in it. Refer to the drive's manual to see if you must set jumpers Connector Power Cable for 3.5-inch Floppy Disk Drive Power Cables for - HP XM600 | hp kayak xm600, installing and replacing hardware parts in your pc wo - Page 14
your PC Workstation. Two of these are for IDE devices. • The ATA IDE cable supports two IDE devices. This cable is connected to the Primary IDE connector on the system board. The , Secondary IDE Cable Refer to the drive's installation guide to check jumper settings or if there is a special installation procedure to - HP XM600 | hp kayak xm600, installing and replacing hardware parts in your pc wo - Page 15
Parts in Your PC Workstation Installing for Plug and Play SCSI hard disks (SCSI hard disks that support the SCAM protocol). The total length of the external SCSI cables should on the SCSI hard disk drive. Refer to the installation guide supplied with the drive for information on selecting a SCSI ID. - HP XM600 | hp kayak xm600, installing and replacing hardware parts in your pc wo - Page 16
Hardware Parts in Your PC Workstation system documentation for information on how to do this. 1 Switch off the display and PC Workstation. Disconnect all power cables and any LAN or telecommunications cables. 2 Remove the PC Workstation's cover and front bezel (refer to page 3 for these instructions - HP XM600 | hp kayak xm600, installing and replacing hardware parts in your pc wo - Page 17
Installing a Second Hard Disk Drive 1 Switch off the display and PC Workstation. Disconnect all power cables and any LAN or telecommunications cables. 2 Remove the PC Workstation's cover and front bezel (refer to page 3 for these instructions). 3 Remove the two retaining screws from the hard disk - HP XM600 | hp kayak xm600, installing and replacing hardware parts in your pc wo - Page 18
display and PC Workstation. Disconnect all power cables and any LAN or telecommunications cables. 2 Remove the PC Workstation's cover and the front bezel (refer to page 2 for instructions). 3 Remove the HP UltraFlow Airflow Guide , such as the HP Zip drive, require an HP-supplied tray before they can - HP XM600 | hp kayak xm600, installing and replacing hardware parts in your pc wo - Page 19
Parts in Your PC Workstation Installing an Accessory in the Front Access Cage 10 Put the front access cage back into the PC. The front access cage retainers should be aligned with the chassis. 11 Connect the power plate in a safe place. 15 Replace the HP UltraFlow Airflow Guide (refer to page 4). 19 - HP XM600 | hp kayak xm600, installing and replacing hardware parts in your pc wo - Page 20
display and PC Workstation. Disconnect all power cables and any LAN or telecommunications cables. 2 Remove the PC Workstation's cover and front bezel (refer to page 3 for these instructions). 3 Refer to page 18 for instruction only. 4 Ensure that the two metal guides on the inside of the chassis on - HP XM600 | hp kayak xm600, installing and replacing hardware parts in your pc wo - Page 21
display and PC Workstation. Disconnect all power cables and any LAN or telecommunications cables. 2 Remove the PC Workstation's cover and front bezel (refer to page 3 for these instructions). 3 Refer to page 18 for instructions 13. 5 Ensure that the two metal guides on the inside of the chassis on - HP XM600 | hp kayak xm600, installing and replacing hardware parts in your pc wo - Page 22
Installing and Replacing Hardware Parts in Your PC Workstation Replacing the Floppy Disk Drive NOTE To that the data and power cables are neatly routed so that they do not interfere with any other device or hinder the PC Workstation's cover. 8 Replace the PC Workstation's cover and front bezel - HP XM600 | hp kayak xm600, installing and replacing hardware parts in your pc wo - Page 23
display and PC Workstation. Disconnect all power cables and any LAN or telecommunications cables. 2 Remove the PC Workstation's cover and front bezel (refer to page 3 for these instructions disk drive bay and speaker assembly towards the system board until it is well clear of the chassis edge ( - HP XM600 | hp kayak xm600, installing and replacing hardware parts in your pc wo - Page 24
Installing and Replacing Hardware Parts in Your PC Workstation Replacing the Hard Disk Drive Bay and cables to their connectors on the system board. 6 Reconnect the data and power cables. Replace the hard disk drive and hard disk drive tray. 7 Replace the PC Workstation's cover and front bezel (refer - HP XM600 | hp kayak xm600, installing and replacing hardware parts in your pc wo - Page 25
Workstation. 2 If an error message appears, follow the instructions system configuration will be updated automatically. 1 Switch on the PC Workstation. 2 To enter the SCSI Configuration Utility press when the message Press to start Configuration Utility... is displayed during the PC Workstation - HP XM600 | hp kayak xm600, installing and replacing hardware parts in your pc wo - Page 26
Parts in Your PC Workstation Replacing the Processor Fan Removing the Processor Fan Replacing the Processor Fan 1 Switch off the display and PC Workstation. Disconnect all power cables and any LAN or telecommunications cables. 2 Remove the PC Workstation's cover (refer to page 2 for instructions - HP XM600 | hp kayak xm600, installing and replacing hardware parts in your pc wo - Page 27
Installing and Replacing Hardware Parts in Your PC Workstation Replacing the Power Supply Unit Replacing the Power Supply Unit WARNING Hewlett-Packard does not support power supply upgrades. This information is provided to help you replace a defective power supply unit. For your safety, only - HP XM600 | hp kayak xm600, installing and replacing hardware parts in your pc wo - Page 28
refer to page 3 for these instructions). 3 Remove the HP UltraFlow Airflow Guide (refer to page 4 for instructions). 4 Disconnect any cables attached to the system board. 5 Move the front access cage forward (described on page 18). 6 Remove the main memory, processor and any accessory cards from the - HP XM600 | hp kayak xm600, installing and replacing hardware parts in your pc wo - Page 29
the HP UltraFlow Airflow Guide (refer to page 4). 8 Replace the PC Workstation's cover and front bezel (refer to page 3). Reconnect all the power and telecommunications cables. 9 After installing the system board, you need to update your BIOS. The latest BIOS for your PC and instructions on updating - HP XM600 | hp kayak xm600, installing and replacing hardware parts in your pc wo - Page 30
and Replacing Hardware Parts in Your PC Workstation System Board Switches System Board Switches There are ten system board switches used for configuration, numbered from 1 to 10. Of these a certain number are reserved and should not be modified, otherwise it could lead to a system failure. Switch - HP XM600 | hp kayak xm600, installing and replacing hardware parts in your pc wo - Page 31
Hardware Parts in Your PC Workstation Replacing or to the dealer from whom you purchased your PC Workstation, or to HP, so that they can be either recycled or disposed of the PC Workstation's power supply cord and any connection to a telecommunications network. 1 Remove the PC Workstation's cover.
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
 |
 |
Installing and Replacing Hardware
Parts in Your PC Workstation
This chapter provides information about installing accessories and
replacing hardware parts in your PC Workstation.
Contact your dealer for an up-to-date list of supported devices or check the
HP web site:
.
Front Access Drives, for
- 5.25-inch drives
- 3.5-inch 1.44 MB
floppy disk drive
Front Access Cage
Up to six accessory cards can be
installed:
- One AGP 4X slot (graphics)
- Five 32-bit PCI slots
Support for one or two
processors
Depending on the model, the memory module sockets support either:
Primary Hard Disk
Drive Bay
Floppy Disk Drive Connector
Primary IDE Connector
Power Supply Unit
Processor Fan
Secondary
Hard Disk
Drive tray
HP UltraFlow
Airflow Guide
Secondary IDE Connector
HP Master Key Lock
•
Two RDRAM modules.
•
Two SDRAM modules installed in a Memory Expansion Card.