HP Xw460c HP BladeSystem c7000 Enclosure Setup and Installation Guide - Page 59

Powering up the enclosure, Single-phase AC configuration

Get HP Xw460c - ProLiant - Blade Workstation PDF manuals and user guides View all HP Xw460c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

Powering up the enclosure Setting up AC power for the enclosure varies depending on whether you have a single-phase AC configuration or a three-phase AC configuration. Single-phase AC configuration To cable the enclosure using a single-phase AC configuration: 1. Connect the AC power cables to the power connectors on the rear of the enclosure corresponding to the power supply that was populated on the front of the enclosure. 2. Be sure each power cable is securely attached to the power connectors. 3. Connect the AC power cables to the AC power source or to an installed power distribution unit (PDU). 4. Turn on the AC circuit breakers that power the power cables installed in the enclosure. 5. Locate the power retention bracket that came with the enclosure. 6. Verify that the power cord retention tabs are on the correct side. o On the left side: To install the power cord retention bracket on the left side of the enclosure, ensure the power cord retention tabs are located to the right of the snap clamps. Cabling and powering up the enclosure 59

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
Cabling and powering up the enclosure
59
Powering up the enclosure
Setting up AC power for the enclosure varies depending on whether you have a single-phase AC
configuration or a three-phase AC configuration.
Single-phase AC configuration
To cable the enclosure using a single-phase AC configuration:
1.
Connect the AC power cables to the power connectors on the rear of the enclosure corresponding to
the power supply that was populated on the front of the enclosure.
2.
Be sure each power cable is securely attached to the power connectors.
3.
Connect the AC power cables to the AC power source or to an installed power distribution unit
(PDU).
4.
Turn on the AC circuit breakers that power the power cables installed in the enclosure.
5.
Locate the power retention bracket that came with the enclosure.
6.
Verify that the power cord retention tabs are on the correct side.
o
On the left side: To install the power cord retention bracket on the left side of the enclosure,
ensure the power cord retention tabs are located to the right of the snap clamps.