HP Z620 HP Workstations - CRU Dataport DX115 kit installation
HP Z620 Manual
View all HP Z620 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP Z620 manual content summary:
- HP Z620 | HP Workstations - CRU Dataport DX115 kit installation - Page 1
- HP Z620 | HP Workstations - CRU Dataport DX115 kit installation - Page 2
- HP Z620 | HP Workstations - CRU Dataport DX115 kit installation - Page 3
case into the optical drive bay ...3 HP Z200 SFF and HP Z210 SFF computers ...4 HP Z200, HP Z210 CMT, HP Z400, and HP xw4000 computers ...9 HP xw6200, HP xw6400, and HP xw6600 computers ...11 HP Z600 and HP Z800 computers ...12 HP xw8000 and HP xw9000 computers ...14 Step 3-Installing a hard disk in - HP Z620 | HP Workstations - CRU Dataport DX115 kit installation - Page 4
iv ENWW - HP Z620 | HP Workstations - CRU Dataport DX115 kit installation - Page 5
key) Installation document Two SATA cables Five M3 screws One 6-32 screw Before you begin To view QuickSpecs and determine the compatibility of this product with your HP computer, see http://www.hp.com/go/productbulletin. © 2006-2011 Hewlett-Packard Development Company, L.P. Microsoft, Windows - HP Z620 | HP Workstations - CRU Dataport DX115 kit installation - Page 6
Guide. It describes proper computer setup, posture, health, and work habits for computer users, and provides important electrical and mechanical safety information. This guide is located at http://www.hp (ESD) precautions while performing the system parts removal and replacement procedures: - Work - HP Z620 | HP Workstations - CRU Dataport DX115 kit installation - Page 7
the service guide for your computer at http://www.hp.com/support/manuals. Power down the computer, and then disconnect the power cord. Power down all external devices, and then disconnect them from the computer. Remove the side access panel. Step 2-Installing the DX115 case into the optical drive - HP Z620 | HP Workstations - CRU Dataport DX115 kit installation - Page 8
Z210 SFF computers To install a DX115 case in an HP Z200 SFF or HP Z210 SFF computer: 1. Remove the front bezel: a. If necessary, remove the Lift the release tabs (1), and then rotate the front bezel off the chassis (2). Figure 3 Removing the front bezel 4 CRU Dataport DX115 kit installation ENWW - HP Z620 | HP Workstations - CRU Dataport DX115 kit installation - Page 9
back away from the bezel and to the left to remove it (2). Figure 4 Removing the bezel blank 3. If an existing optical disk drive is present, remove it: a. Rotate the drive cage to its upright position. Figure 5 Rotating the drive cage up ENWW Step 2-Installing the DX115 case into the optical - HP Z620 | HP Workstations - CRU Dataport DX115 kit installation - Page 10
button located on the left side of the drive to disengage the drive from the drive cage. While pressing the drive retainer button, slide the drive back until it stops, then lift it up and out of the drive cage. Figure 7 Removing the optical drive 6 CRU Dataport DX115 kit installation ENWW - HP Z620 | HP Workstations - CRU Dataport DX115 kit installation - Page 11
holes of the DX115 case. Spare M3 screws supplied with your workstation are mounted on its chassis near the optical bay. Figure 9 Installing the guide screws 6. Position the guide screws on the drive into the J-slots in the drive bay. Then slide the drive toward the front of the computer until it - HP Z620 | HP Workstations - CRU Dataport DX115 kit installation - Page 12
or lowering it. One guide is located on the bottom side of the drive cage. The other is part of the chassis frame under the drive cage. Route the data cable through these guides before connecting it to the optical drive. Figure 12 Routing the drive cable 8 CRU Dataport DX115 kit installation ENWW - HP Z620 | HP Workstations - CRU Dataport DX115 kit installation - Page 13
the power and data cables 10. Carefully rotate the drive cage back down to its normal position. CAUTION: Check clearances on the cables when you rotate the drive cage. The cage may pinch the cables and damage them if they are not routed correctly. HP Z200, HP Z210 CMT, HP Z400, and HP xw4000 - HP Z620 | HP Workstations - CRU Dataport DX115 kit installation - Page 14
9 Installing the guide screws on page 7. Spare M3 screws are supplied with your workstation and mounted on its chassis near Installing the DX115 case in an HP Z210 CMT and HP Z400 workstation mini-tower configuration 4. Figure 16 Installing the DX115 case in an HP Z210 CMT desktop configuration - HP Z620 | HP Workstations - CRU Dataport DX115 kit installation - Page 15
x 5mm screws are located on the chassis front side under the bezel. CAUTION: Failure to install the shipping screw might result in damage to the removable hard drive system. Figure 17 Installing the shipping support screw HP xw6200, HP xw6400, and HP xw6600 computers 1. 2. 3. Remove the front bezel - HP Z620 | HP Workstations - CRU Dataport DX115 kit installation - Page 16
to the removable hard drive system. Figure 19 Installing the shipping support screw HP Z600 and HP Z800 computers 1. For HP Z800 computers: ● ● 2. 3. Remove the airflow guide to enable access to the optical bays. Remove the card support to enable access to the system board connectors. Remove and - HP Z620 | HP Workstations - CRU Dataport DX115 kit installation - Page 17
one (supplied) M3 x 5mm screw (black) for each DX115 unit for shipping support. CAUTION: Failure to install the shipping screw might result in damage to the removable hard drive system. Figure 21 Installing the shipping support screw ENWW Step 2-Installing the DX115 case into the optical drive bay - HP Z620 | HP Workstations - CRU Dataport DX115 kit installation - Page 18
DX115 unit for shipping support. Spare M3 screws supplied with your workstation are mounted on its chassis. CAUTION: Failure to install the shipping screw might result in damage to the removable hard drive system. Figure 23 Installing the shipping support screw Step 3-Installing a hard disk in the - HP Z620 | HP Workstations - CRU Dataport DX115 kit installation - Page 19
, or even drive damage. The component supplier's user guide describes a procedure for inserting or removing the carrier (with drive) while the workstation is booted and then powering the drive via the power switch on the enclosure. Microsoft Windows XP and Windows Vista do not support this action - HP Z620 | HP Workstations - CRU Dataport DX115 kit installation - Page 20
the way to the rear end of the carrier so that the power and data connectors mate with the carrier adapter. Figure 26 Installing the drive 6. Replace the cover by aligning the tab on the rear of the cover with the slot on the rear of the carrier (1) and then rotating - HP Z620 | HP Workstations - CRU Dataport DX115 kit installation - Page 21
supplier's user guide describes a procedure for inserting or removing the carrier (with drive) while the workstation is booted and then powering the drive via the power switch on the enclosure. Microsoft Windows XP and Windows Vista do not support this action. 1. After the drive case is installed in - HP Z620 | HP Workstations - CRU Dataport DX115 kit installation - Page 22
with the lowestnumbered available port. For HP Z400 and Z600 computers, the blind-mate cables for the internal hard drive bays may require adjustment at the system board, based on the computer drive configuration. Consult the User Guide or the Maintenance and Service Guide for your computer for