HP t5400 Troubleshooting Guide: HP t5400 Thin Client - Page 18

Replacing the Side Access Panel, Installing Thin Client Options, Removing and Replacing the Battery - review

Get HP t5400 - Thin Client PDF manuals and user guides View all HP t5400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Replacing the Side Access Panel To replace the access panel: 1. Align the tabs on the access panel with the slots in the both sides of the chassis and place the access panel on the side of the unit, offset about 8.3 mm (1/3 inch) toward the top of the unit (1). 2. Slide the panel toward the front of the unit until the panel is flush with the bottom panel of the chassis (2). 3. Insert and fasten the two screws to secure the side access panel to the chassis. Installing Thin Client Options Various options can be installed on the thin client: ● Removing and Replacing the Battery on page 10 ● External Drives on page 11 Removing and Replacing the Battery Before beginning the replacement process, review General Hardware Installation Sequence on page 8 for procedures you should follow before and after installing or replacing hardware. WARNING! Before removing the side access panel, ensure that the thin client is turned off and the power cord is disconnected from the electrical outlet. To remove and replace the battery: 1. Locate the battery on the system board. 10 Chapter 2 Hardware Changes

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
Replacing the Side Access Panel
To replace the access panel:
1.
Align the tabs on the access panel with the slots in the both sides of the chassis and place the
access panel on the side of the unit, offset about 8.3 mm (1/3 inch) toward the top of the unit (1).
2.
Slide the panel toward the front of the unit until the panel is flush with the bottom panel of the
chassis (2).
3.
Insert and fasten the two screws to secure the side access panel to the chassis.
Installing Thin Client Options
Various options can be installed on the thin client:
●
Removing and Replacing the Battery
on page
10
●
External Drives
on page
11
Removing and Replacing the Battery
Before beginning the replacement process, review
General Hardware Installation Sequence
on page
8
for procedures you should follow before and after installing or replacing hardware.
WARNING!
Before removing the side access panel, ensure that the thin client is turned off and the
power cord is disconnected from the electrical outlet.
To remove and replace the battery:
1.
Locate the battery on the system board.
10
Chapter 2
Hardware Changes