Honeywell 6271C User Guide - Page 16

How to Display Faults

Get Honeywell 6271C - Ademco TouchCenter Color Keypad PDF manuals and user guides
UPC - 781410790247
View all Honeywell 6271C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Security System Operation (cont'd) How to Display Faults The Display Faults function is used when you see a Not Ready Fault message and want to determine were the fault is and what type of fault it is. To display faults do the following: 1. From the "Home" screen, press the SECURITY button. The "Arming" screen is displayed. SCREEN ACTION 2. From the "Arming" screen, press the DISPLAY FAULTS button. The "Display Faults" screen is displayed showing a listing of faulted and/or bypassed zones. The following symbols may be displayed on the "Display Faults" screen. Zone in alarm Zone has trouble Zone is faulted Zone has low battery Zone is bypassed 3. As applicable, take corrective action such as closing a window or door to correct the fault. If the fault cannot be corrected, you may chose to bypass a zone by touching the zone to select it and depressing the BYPASS SELECTED button or bypass all faulted zones by depressing the BYPASS ALL button. The "User Authorization" screen is displayed with the instructions "To Bypass Zones, Enter Code". • Residential systems will not allow you to bypass fire or emergency zones. On commercial systems, a specified user may be allowed to bypass fire and system zones if the user was enabled by your system installer. • To bypass zones the system must be disarmed first. • Limits apply as to how many zones can be bypassed at one time. These limits are ten zones on residential and five zones on commercial systems. 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
Security System Operation (cont'd)
16
How to Display Faults
The Display Faults function is used when you see a Not Ready Fault
message and want to determine were the fault is and what type of
fault it is.
To display faults do the following:
1.
From the "Home" screen, press the
SECURITY
button.
The "Arming" screen
is displayed.
SCREEN
ACTION
2.
From the "Arming" screen, press the
DISPLAY FAULTS
button.
The "Display
Faults" screen is displayed showing a
listing of faulted and/or bypassed zones.
The following symbols may be displayed
on the "Display Faults" screen.
Zone in alarm
Zone has trouble
Zone is faulted
Zone has low battery
Zone is bypassed
3.
As applicable, take corrective action
such as closing a window or door to
correct the fault. If the fault cannot be
corrected, you may chose to bypass a
zone by touching the zone to select it and
depressing the
BYPASS SELECTED
button or bypass all faulted zones by
depressing the
BYPASS ALL
button.
The "User Authorization" screen is
displayed with the instructions "
To
Bypass Zones, Enter Code
".
•
Residential systems will not allow you to bypass fire or emergency
zones. On commercial systems, a specified user may be allowed to
bypass fire and system zones if the user was enabled by your system
installer.
•
To bypass zones the system must be disarmed first.
•
Limits apply as to how many zones can be bypassed at one time.
These limits are ten zones on residential and five zones on
commercial systems.